diff --git a/.github/workflows/build.yml b/.github/workflows/build.yml
index 492881f320..6432c665c7 100644
--- a/.github/workflows/build.yml
+++ b/.github/workflows/build.yml
@@ -39,8 +39,10 @@ jobs:
- "esp32dev-rtl_433"
- "esp32doitv1-aithinker-r01-sx1278"
- "heltec-rtl_433"
+ - "heltec-rtl_433-fsk"
- "heltec-ble"
- "lilygo-rtl_433"
+ - "lilygo-rtl_433-fsk"
- "lilygo-ble"
- "esp32dev-multi_receiver"
- "esp32dev-multi_receiver-pilight"
diff --git a/docs/use/rf.md b/docs/use/rf.md
index a5f48e64b6..ea4283e7ec 100644
--- a/docs/use/rf.md
+++ b/docs/use/rf.md
@@ -124,19 +124,19 @@ Registering protocol [102] "X10 Security"
### Change receive frequency
-Default receive frequency of the module is 433.92 Mhz, and this can be can changed by sending a message with the frequency. Parameter is `mhz` and valid values are 300-348 Mhz, 387-464Mhz and 779-928Mhz. Actual frequency support will depend on your board
+The frequency can be can changed by sending an MQTT message or through the WebUI. Parameter is `frequency` and valid values are 300-348 Mhz, 387-464Mhz and 779-928Mhz. Actual frequency support will depend on your board
-`home/OpenMQTTGateway/commands/MQTTtoRTL_433 {"mhz":315.026}`
+`home/OpenMQTTGateway/commands/MQTTtoRF/config {"frequency":315.026}`
### Change Signal RSSI Threshold Delta
Delta applied to RSSI floor noise level to determine start and end of signal, defaults to 9db.
-`home/OpenMQTTGateway/commands/MQTTtoRTL_433 {"rssi": 9}`
+`home/OpenMQTTGateway/commands/MQTTtoRF/config {"rssiThreshold": 9}`
### Retrieve current status of receiver
-`home/OpenMQTTGateway/commands/MQTTtoRTL_433 {"status":1}`
+`home/OpenMQTTGateway/commands/MQTTtoRF/config {"status":1}`
```
{"model":"status",
@@ -159,41 +159,27 @@ Delta applied to RSSI floor noise level to determine start and end of signal, de
"freeMem":112880} - ESP32 memory available
```
-
## Changing Active Receiver Modules
### Switching Active Receiver Module
-Switching of the active transceiver (RTL_433 receiver only) module is available between the RF, RF2, RTL_433 and Pilight gateway modules, allowing for changing of signal decoders without redeploying the openMQTTGateway package. Sending a JSON message to the command topic of the desired receiver will change the active transceiver module.
+Switching of the active transceiver (RTL_433 receiver only) module is available between the RF, RF2, and (RTL_433 or Pilight) gateway modules, allowing for changing of signal decoders without redeploying the openMQTTGateway package. Sending a JSON message to the command topic will change the active transceiver module.
To enable the RF gateway module send a json message to the RF gateway module command subject with the key being 'active', and any value. The value at this time is ignored.
-Example:
-`mosquitto_pub -t "home/OpenMQTTGateway/commands/MQTTto433" -m '{"active":true}'`
-
-To enable the PiLight gateway module send a json message to the PiLight gateway module command subject with the key being 'active', and any value. The value at this time is ignored.
-
-Example:
-`mosquitto_pub -t "home/OpenMQTTGateway/commands/MQTTtoPilight" -m '{"active":true}'`
-
-To enable the RF2 gateway module send a json message to the RF2 gateway module command subject with the key being 'active', and any value. The value at this time is ignored.
-
-Example:
-`mosquitto_pub -t "home/OpenMQTTGateway/commands/MQTTtoRF2" -m '{"active":true}'`
+1 - PiLight
+2 - RF
+3 - RTL_433
+4 - RF2
-To enable the RTL_433 gateway module send a json message to the RTL_433 gateway module command subject with the key being 'active', and any value. The value at this time is ignored.
+Example to receive from the RF gateway:
+`mosquitto_pub -t "home/OpenMQTTGateway/commands/MQTTtoRF/config" -m '{"active":2}'`
-Example:
-`mosquitto_pub -t "home/OpenMQTTGateway/commands/MQTTtoRTL_433" -m '{"active":true}'`
+The active receiver can also be changed with the WebUI.
### Status Messages
-The openMQTTGateway status message contains a key `actRec` which is the current active receiver module.
-
-1 - PiLight
-2 - RF
-3 - RTL_433
-4 - RF2
+The openMQTTGateway RFtoMQTT status message contains a key `active` which is the current active receiver module.
## RCSwitch based gateway
diff --git a/environments.ini b/environments.ini
index 27928300a2..b06ffe4e4a 100644
--- a/environments.ini
+++ b/environments.ini
@@ -728,6 +728,7 @@ board_build.partitions = min_spiffs.csv
lib_deps =
${com-esp32.lib_deps}
${libraries.rtl_433_ESP}
+ ${libraries.smartrc-cc1101-driver-lib}
build_flags =
${com-esp32.build_flags}
; *** OpenMQTTGateway Config ***
@@ -787,6 +788,40 @@ build_flags =
; '-DDISPLAY_BRIGHTNESS=80'
; '-DDISPLAY_METRIC=false'
custom_description = Gateway using RTL_433_ESP and RadioLib
+custom_hardware = ESP32 HELTEC LORA32 V2
+
+[env:heltec-rtl_433-fsk]
+platform = ${com.esp32_platform}
+board = heltec_wifi_lora_32_V2
+; ~/.platformio/packages/framework-arduinoespressif32/variants/.../pins_arduino.h
+board_build.partitions = min_spiffs.csv
+lib_deps =
+ ${com-esp32.lib_deps}
+ ${libraries.ssd1306}
+ ${libraries.rtl_433_ESP}
+build_flags =
+ ${com-esp32.build_flags}
+; *** OpenMQTTGateway Config ***
+ ;'-UZmqttDiscovery' ; disables MQTT Discovery
+ '-DvalueAsATopic=true' ; MQTT topic includes model and device
+ '-DGateway_Name="OMG_heltec_rtl_433_ESP"'
+ '-DOOK_MODULATION=false' ; FSK modulation activated
+ '-DRF_FREQUENCY=915'
+ ;-DRF_FREQUENCY=868.300'
+ ;-DRF_FREQUENCY=433.9'
+; *** OpenMQTTGateway Modules ***
+ '-DZgatewayRTL_433="rtl_433"'
+ '-DZradioSX127x="SX127x"'
+; *** ssd1306 Display Options ***
+ '-DZdisplaySSD1306="HELTEC_SSD1306"'
+; '-DLOG_TO_OLED=false' ; Enable log to OLED
+; '-DJSON_TO_OLED=true'
+; '-DLOG_LEVEL_OLED=LOG_LEVEL_NOTICE'
+; '-DDISPLAY_IDLE_LOGO=false'
+; '-DDISPLAY_BRIGHTNESS=80'
+; '-DDISPLAY_METRIC=false'
+custom_description = Gateway using RTL_433_ESP and RadioLib
+custom_hardware = ESP32 HELTEC LORA32 V2
[env:heltec-ble]
platform = ${com.esp32_platform}
@@ -810,6 +845,7 @@ build_flags =
; '-DDISPLAY_BRIGHTNESS=80'
; '-DDISPLAY_METRIC=false'
custom_description = Heltec BLE gateway with adaptive scanning activated, automatically adapts the scan parameters depending on your devices
+custom_hardware = ESP32 HELTEC LORA32 V2
[env:lilygo-rtl_433]
platform = ${com.esp32_platform}
@@ -840,6 +876,39 @@ build_flags =
custom_description = For ESP32, Gateway using RTL_433_ESP and RadioLib
custom_hardware = ESP32 LILYGO LoRa32 V2.1
+[env:lilygo-rtl_433-fsk]
+platform = ${com.esp32_platform}
+board = ttgo-lora32-v21
+; ~/.platformio/packages/framework-arduinoespressif32/variants/.../pins_arduino.h
+board_build.partitions = min_spiffs.csv
+lib_deps =
+ ${com-esp32.lib_deps}
+ ${libraries.ssd1306}
+ ${libraries.rtl_433_ESP}
+build_flags =
+ ${com-esp32.build_flags}
+; *** OpenMQTTGateway Config ***
+ ;'-UZmqttDiscovery' ; disables MQTT Discovery
+ '-DvalueAsATopic=true' ; MQTT topic includes model and device
+ '-DGateway_Name="OMG_lilygo_rtl_433_ESP"'
+ '-DOOK_MODULATION=false' ; FSK modulation activated
+ '-DRF_FREQUENCY=915'
+ ;-DRF_FREQUENCY=868.300'
+ ;-DRF_FREQUENCY=433.9'
+; *** OpenMQTTGateway Modules ***
+ '-DZgatewayRTL_433="rtl_433"'
+ '-DZradioSX127x="SX127x"'
+; *** ssd1306 Display Options ***
+ '-DZdisplaySSD1306="LilyGo_SSD1306"'
+; '-DLOG_TO_OLED=true' ; Enable log to OLED
+; '-DJSON_TO_OLED=true'
+; '-DLOG_LEVEL_OLED=LOG_LEVEL_NOTICE'
+; '-DDISPLAY_IDLE_LOGO=false'
+; '-DDISPLAY_BRIGHTNESS=80'
+; '-DDISPLAY_METRIC=false'
+custom_description = For ESP32, Gateway using RTL_433_ESP and RadioLib with FSK modulation (beta)
+custom_hardware = ESP32 LILYGO LoRa32 V2.1
+
[env:lilygo-ble]
platform = ${com.esp32_platform}
board = ttgo-lora32-v21
@@ -920,7 +989,6 @@ build_flags =
; '-DRF_MODULE_INIT_STATUS=true' ; Display transceiver config during startup
custom_description = Multi RF library with the possibility to switch between ESPilight, NewRemoteSwitch and RCSwitch, need CC1101
-
[env:tinypico-ble]
platform = ${com.esp32_platform}
board = tinypico
diff --git a/main/ZactuatorSomfy.ino b/main/ZactuatorSomfy.ino
index 6e8b907463..8c0412b906 100644
--- a/main/ZactuatorSomfy.ino
+++ b/main/ZactuatorSomfy.ino
@@ -34,9 +34,6 @@
# endif
void setupSomfy() {
-# ifdef ZradioCC1101 //using with CC1101
- ELECHOUSE_cc1101.Init();
-# endif
pinMode(RF_EMITTER_GPIO, OUTPUT);
digitalWrite(RF_EMITTER_GPIO, LOW);
@@ -55,7 +52,7 @@ void setupSomfy() {
void MQTTtoSomfy(char* topicOri, JsonObject& jsonData) {
if (cmpToMainTopic(topicOri, subjectMQTTtoSomfy)) {
# ifdef ZradioCC1101
- ELECHOUSE_cc1101.SetTx(CC1101_FREQUENCY_SOMFY);
+ ELECHOUSE_cc1101.SetTx(RF_FREQUENCY_SOMFY);
# endif
Log.trace(F("MQTTtoSomfy json data analysis" CR));
@@ -72,9 +69,7 @@ void MQTTtoSomfy(char* topicOri, JsonObject& jsonData) {
EEPROMRollingCodeStorage rollingCodeStorage(EEPROM_ADDRESS_START + remoteIndex * 2);
SomfyRemote somfyRemote(RF_EMITTER_GPIO, somfyRemotes[remoteIndex], &rollingCodeStorage);
somfyRemote.sendCommand(command, repeat);
-# ifdef ZradioCC1101
- ELECHOUSE_cc1101.SetRx(receiveMhz); // set Receive on
-# endif
+ initCC1101();
}
}
# endif
diff --git a/main/ZcommonRF.ino b/main/ZcommonRF.ino
new file mode 100644
index 0000000000..2aa7ccb057
--- /dev/null
+++ b/main/ZcommonRF.ino
@@ -0,0 +1,334 @@
+/*
+ OpenMQTTGateway - ESP8266 or Arduino program for home automation
+
+ Act as a wifi or ethernet gateway between your BLE/433mhz/infrared IR signal and an MQTT broker
+ Send and receiving command by MQTT
+
+ Copyright: (c)Florian ROBERT
+
+ This file is part of OpenMQTTGateway.
+
+ OpenMQTTGateway is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ OpenMQTTGateway is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+
+#include "User_config.h"
+
+#if defined(ZgatewayRF) || defined(ZgatewayPilight) || defined(ZgatewayRTL_433) || defined(ZgatewayRF2) || defined(ZactuatorSomfy)
+# ifndef ARDUINO_AVR_UNO
+
+# ifdef ZradioCC1101
+# include
+# endif
+
+void initCC1101() {
+# ifdef ZradioCC1101 //receiving with CC1101
+ // Loop on getCC1101() until it returns true and break after 10 attempts
+ for (int i = 0; i < 10; i++) {
+ if (ELECHOUSE_cc1101.getCC1101()) {
+ Log.notice(F("C1101 spi Connection OK" CR));
+ ELECHOUSE_cc1101.Init();
+ ELECHOUSE_cc1101.SetRx(RFConfig.frequency);
+ break;
+ } else {
+ Log.error(F("C1101 spi Connection Error" CR));
+ delay(500);
+ }
+ }
+# endif
+}
+
+void setupCommonRF() {
+ RFConfig_init();
+ RFConfig_load();
+}
+
+bool validFrequency(float mhz) {
+ // CC1101 valid frequencies 300-348 MHZ, 387-464MHZ and 779-928MHZ.
+ if (mhz >= 300 && mhz <= 348)
+ return true;
+ if (mhz >= 387 && mhz <= 464)
+ return true;
+ if (mhz >= 779 && mhz <= 928)
+ return true;
+ return false;
+}
+
+int currentReceiver = ACTIVE_NONE;
+
+# if !defined(ZgatewayRFM69) && !defined(ZactuatorSomfy)
+# if defined(ESP8266) || defined(ESP32)
+// Check if a receiver is available
+bool validReceiver(int receiver) {
+ switch (receiver) {
+# ifdef ZgatewayPilight
+ case ACTIVE_PILIGHT:
+ return true;
+# endif
+# ifdef ZgatewayRF
+ case ACTIVE_RF:
+ return true;
+# endif
+# ifdef ZgatewayRTL_433
+ case ACTIVE_RTL:
+ return true;
+# endif
+# ifdef ZgatewayRF2
+ case ACTIVE_RF2:
+ return true;
+# endif
+ default:
+ Log.error(F("ERROR: stored receiver %d not available" CR), receiver);
+ }
+ return false;
+}
+# endif
+# endif
+
+void disableCurrentReceiver() {
+ Log.trace(F("disableCurrentReceiver: %d" CR), currentReceiver);
+ switch (currentReceiver) {
+ case ACTIVE_NONE:
+ break;
+# ifdef ZgatewayPilight
+ case ACTIVE_PILIGHT:
+ disablePilightReceive();
+ break;
+# endif
+# ifdef ZgatewayRF
+ case ACTIVE_RF:
+ disableRFReceive();
+ break;
+# endif
+# ifdef ZgatewayRTL_433
+ case ACTIVE_RTL:
+ disableRTLreceive();
+ break;
+# endif
+# ifdef ZgatewayRF2
+ case ACTIVE_RF2:
+ disableRF2Receive();
+ break;
+# endif
+# ifndef ARDUINO_AVR_UNO // Space issues with the UNO
+ default:
+ Log.error(F("ERROR: unsupported receiver %d" CR), RFConfig.activeReceiver);
+# endif
+ }
+}
+
+void enableActiveReceiver() {
+ Log.trace(F("enableActiveReceiver: %d" CR), RFConfig.activeReceiver);
+ switch (RFConfig.activeReceiver) {
+# ifdef ZgatewayPilight
+ case ACTIVE_PILIGHT:
+ initCC1101();
+ enablePilightReceive();
+ currentReceiver = ACTIVE_PILIGHT;
+ break;
+# endif
+# ifdef ZgatewayRF
+ case ACTIVE_RF:
+ initCC1101();
+ enableRFReceive();
+ currentReceiver = ACTIVE_RF;
+ break;
+# endif
+# ifdef ZgatewayRTL_433
+ case ACTIVE_RTL:
+ initCC1101();
+ enableRTLreceive();
+ currentReceiver = ACTIVE_RTL;
+ break;
+# endif
+# ifdef ZgatewayRF2
+ case ACTIVE_RF2:
+ initCC1101();
+ enableRF2Receive();
+ currentReceiver = ACTIVE_RF2;
+ break;
+# endif
+ case ACTIVE_RECERROR:
+ Log.error(F("ERROR: no receiver selected" CR));
+ break;
+# ifndef ARDUINO_AVR_UNO // Space issues with the UNO
+ default:
+ Log.error(F("ERROR: unsupported receiver %d" CR), RFConfig.activeReceiver);
+# endif
+ }
+}
+
+String stateRFMeasures() {
+ //Publish RTL_433 state
+ StaticJsonDocument jsonBuffer;
+ JsonObject RFdata = jsonBuffer.to();
+ RFdata["active"] = RFConfig.activeReceiver;
+# if defined(ZradioCC1101) || defined(ZradioSX127x)
+ RFdata["frequency"] = RFConfig.frequency;
+ if (RFConfig.activeReceiver == ACTIVE_RTL) {
+# ifdef ZgatewayRTL_433
+ RFdata["rssithreshold"] = (int)getRTLrssiThreshold();
+ RFdata["rssi"] = (int)getRTLCurrentRSSI();
+ RFdata["avgrssi"] = (int)getRTLAverageRSSI();
+ RFdata["count"] = (int)getRTLMessageCount();
+# endif
+# ifdef ZradioSX127x
+ RFdata["ookthreshold"] = (int)getOOKThresh();
+# endif
+ }
+# endif
+ pub(subjectcommonRFtoMQTT, RFdata);
+
+ String output;
+ serializeJson(RFdata, output);
+ return output;
+}
+
+void RFConfig_fromJson(JsonObject& RFdata) {
+ bool success = false;
+ if (RFdata.containsKey("frequency") && validFrequency(RFdata["frequency"])) {
+ Config_update(RFdata, "frequency", RFConfig.frequency);
+ Log.notice(F("RF Receive mhz: %F" CR), RFConfig.frequency);
+ success = true;
+ }
+ if (RFdata.containsKey("active")) {
+ Log.notice(F("RF receiver active: %d" CR), RFConfig.activeReceiver);
+ Config_update(RFdata, "active", RFConfig.activeReceiver);
+ success = true;
+ }
+# ifdef ZgatewayRTL_433
+ if (RFdata.containsKey("rssithreshold")) {
+ Log.notice(F("RTL_433 RSSI Threshold : %d " CR), RFConfig.rssiThreshold);
+ Config_update(RFdata, "rssithreshold", RFConfig.rssiThreshold);
+ rtl_433.setRSSIThreshold(RFConfig.rssiThreshold);
+ success = true;
+ }
+# if defined(RF_SX1276) || defined(RF_SX1278)
+ if (RFdata.containsKey("ookthreshold")) {
+ Config_update(RFdata, "ookthreshold", RFConfig.newOokThreshold);
+ Log.notice(F("RTL_433 ookThreshold %d" CR), RFConfig.newOokThreshold);
+ rtl_433.setOOKThreshold(RFConfig.newOokThreshold);
+ success = true;
+ }
+# endif
+ if (RFdata.containsKey("status")) {
+ Log.notice(F("RF get status:" CR));
+ rtl_433.getStatus();
+ success = true;
+ }
+ if (!success) {
+ Log.error(F("MQTTtoRF Fail json" CR));
+ }
+# endif
+ disableCurrentReceiver();
+ enableActiveReceiver();
+# ifdef ESP32
+ if (RFdata.containsKey("erase") && RFdata["erase"].as()) {
+ // Erase config from NVS (non-volatile storage)
+ preferences.begin(Gateway_Short_Name, false);
+ if (preferences.isKey("RFConfig")) {
+ int result = preferences.remove("RFConfig");
+ Log.notice(F("RF config erase result: %d" CR), result);
+ preferences.end();
+ return; // Erase prevails on save, so skipping save
+ } else {
+ Log.notice(F("RF config not found" CR));
+ preferences.end();
+ }
+ }
+ if (RFdata.containsKey("save") && RFdata["save"].as()) {
+ StaticJsonDocument jsonBuffer;
+ JsonObject jo = jsonBuffer.to();
+ jo["frequency"] = RFConfig.frequency;
+ jo["active"] = RFConfig.activeReceiver;
+// Don't save those for now, need to be tested
+# ifdef ZgatewayRTL_433
+//jo["rssithreshold"] = RFConfig.rssiThreshold;
+//jo["ookthreshold"] = RFConfig.newOokThreshold;
+# endif
+ // Save config into NVS (non-volatile storage)
+ String conf = "";
+ serializeJson(jsonBuffer, conf);
+ preferences.begin(Gateway_Short_Name, false);
+ int result = preferences.putString("RFConfig", conf);
+ preferences.end();
+ Log.notice(F("RF Config_save: %s, result: %d" CR), conf.c_str(), result);
+ }
+# endif
+}
+
+void RFConfig_init() {
+ RFConfig.frequency = RF_FREQUENCY;
+ RFConfig.activeReceiver = ACTIVE_RECEIVER;
+ RFConfig.rssiThreshold = 0;
+ RFConfig.newOokThreshold = 0;
+}
+
+void RFConfig_load() {
+# ifdef ESP32
+ StaticJsonDocument jsonBuffer;
+ preferences.begin(Gateway_Short_Name, true);
+ if (preferences.isKey("RFConfig")) {
+ auto error = deserializeJson(jsonBuffer, preferences.getString("RFConfig", "{}"));
+ preferences.end();
+ if (error) {
+ Log.error(F("RF Config deserialization failed: %s, buffer capacity: %u" CR), error.c_str(), jsonBuffer.capacity());
+ return;
+ }
+ if (jsonBuffer.isNull()) {
+ Log.warning(F("RF Config is null" CR));
+ return;
+ }
+ JsonObject jo = jsonBuffer.as();
+ RFConfig_fromJson(jo);
+ Log.notice(F("RF Config loaded" CR));
+ } else {
+ preferences.end();
+ Log.notice(F("RF Config not found using default" CR));
+ enableActiveReceiver();
+ }
+# else
+ enableActiveReceiver();
+# endif
+}
+
+void MQTTtoRFset(char* topicOri, JsonObject& RFdata) {
+ if (cmpToMainTopic(topicOri, subjectMQTTtoRFset)) {
+ Log.trace(F("MQTTtoRF json set" CR));
+
+ /*
+ * Configuration modifications priorities:
+ * First `init=true` and `load=true` commands are executed (if both are present, INIT prevails on LOAD)
+ * Then parameters included in json are taken in account
+ * Finally `erase=true` and `save=true` commands are executed (if both are present, ERASE prevails on SAVE)
+ */
+ if (RFdata.containsKey("init") && RFdata["init"].as()) {
+ // Restore the default (initial) configuration
+ RFConfig_init();
+ } else if (RFdata.containsKey("load") && RFdata["load"].as()) {
+ // Load the saved configuration, if not initialised
+ RFConfig_load();
+ }
+
+ // Load config from json if available
+ RFConfig_fromJson(RFdata);
+ stateRFMeasures();
+ }
+}
+# else
+void RFConfig_init() {}
+void RFConfig_load() {}
+void MQTTtoRFset(char* topicOri, JsonObject& RFdata) {}
+void enableActiveReceiver() {}
+# endif
+#endif
diff --git a/main/ZgatewayPilight.ino b/main/ZgatewayPilight.ino
index 9226b0197e..020ce7dc1e 100644
--- a/main/ZgatewayPilight.ino
+++ b/main/ZgatewayPilight.ino
@@ -112,21 +112,6 @@ void pilightRawCallback(const uint16_t* pulses, size_t length) {
}
# endif
-void setupPilight() {
-# ifdef ZradioCC1101 //receiving with CC1101
- ELECHOUSE_cc1101.Init();
- ELECHOUSE_cc1101.setMHZ(CC1101_FREQUENCY);
- ELECHOUSE_cc1101.SetRx(CC1101_FREQUENCY);
-# endif
- rf.setCallback(pilightCallback);
- rf.initReceiver(RF_RECEIVER_GPIO);
- pinMode(RF_EMITTER_GPIO, OUTPUT); // Set this here, because if this is the RX pin it was reset to INPUT by Serial.end();
- Log.notice(F("RF_EMITTER_GPIO: %d " CR), RF_EMITTER_GPIO);
- Log.notice(F("RF_RECEIVER_GPIO: %d " CR), RF_RECEIVER_GPIO);
- Log.trace(F("ZgatewayPilight command topic: %s%s%s" CR), mqtt_topic, gateway_name, subjectMQTTtoPilight);
- Log.trace(F("ZgatewayPilight setup done " CR));
-}
-
void savePilightConfig() {
Log.trace(F("saving Pilight config" CR));
DynamicJsonDocument json(4096);
@@ -231,13 +216,10 @@ void MQTTtoPilight(char* topicOri, JsonObject& Pilightdata) {
}
int msgLength = rf.stringToPulseTrain(raw, codes, MAXPULSESTREAMLENGTH);
if (msgLength > 0) {
-# ifdef ZradioCC1101
- disableActiveReceiver();
- ELECHOUSE_cc1101.Init();
+ disableCurrentReceiver();
+ initCC1101();
pinMode(RF_EMITTER_GPIO, OUTPUT);
- ELECHOUSE_cc1101.SetTx(receiveMhz); // set Transmit on
rf.disableReceiver();
-# endif
rf.sendPulseTrain(codes, msgLength, repeats);
Log.notice(F("MQTTtoPilight raw ok" CR));
success = true;
@@ -262,13 +244,10 @@ void MQTTtoPilight(char* topicOri, JsonObject& Pilightdata) {
}
if (message && protocol) {
Log.trace(F("MQTTtoPilight msg & protocol ok" CR));
-# ifdef ZradioCC1101
- disableActiveReceiver();
- ELECHOUSE_cc1101.Init();
+ disableCurrentReceiver();
+ initCC1101();
pinMode(RF_EMITTER_GPIO, OUTPUT);
- ELECHOUSE_cc1101.SetTx(receiveMhz); // set Transmit on
rf.disableReceiver();
-# endif
int msgLength = rf.send(protocol, message);
if (msgLength > 0) {
Log.trace(F("Adv data MQTTtoPilight push state via PilighttoMQTT" CR));
@@ -294,18 +273,6 @@ void MQTTtoPilight(char* topicOri, JsonObject& Pilightdata) {
}
}
}
- if (Pilightdata.containsKey("active")) {
- Log.trace(F("PiLight active:" CR));
- activeReceiver = ACTIVE_PILIGHT; // Enable PILIGHT gateway
- success = true;
- }
-# ifdef ZradioCC1101
- if (Pilightdata.containsKey("mhz") && validFrequency(tempMhz)) {
- receiveMhz = tempMhz;
- Log.notice(F("PiLight Receive mhz: %F" CR), receiveMhz);
- success = true;
- }
-# endif
if (success) {
// we acknowledge the sending by publishing the value to an acknowledgement topic, for the moment even if it is a signal repetition we acknowledge also
pub(subjectGTWPilighttoMQTT, Pilightdata);
@@ -313,7 +280,7 @@ void MQTTtoPilight(char* topicOri, JsonObject& Pilightdata) {
pub(subjectGTWPilighttoMQTT, "{\"Status\": \"Error\"}"); // Fail feedback
Log.error(F("MQTTtoPilight Fail json" CR));
}
- enableActiveReceiver(false);
+ enableActiveReceiver();
}
}
@@ -324,25 +291,13 @@ extern void disablePilightReceive() {
};
extern void enablePilightReceive() {
-# ifdef ZradioCC1101
- Log.notice(F("Switching to Pilight Receiver: %F" CR), receiveMhz);
-# else
- Log.notice(F("Switching to Pilight Receiver" CR));
-# endif
-# ifdef ZgatewayRF
- disableRFReceive();
-# endif
-# ifdef ZgatewayRF2
- disableRF2Receive();
-# endif
-# ifdef ZgatewayRTL_433
- disableRTLreceive();
-# endif
+ Log.notice(F("Switching to Pilight Receiver: %F" CR), RFConfig.frequency);
+ Log.notice(F("RF_EMITTER_GPIO: %d " CR), RF_EMITTER_GPIO);
+ Log.notice(F("RF_RECEIVER_GPIO: %d " CR), RF_RECEIVER_GPIO);
+ Log.trace(F("ZgatewayPilight command topic: %s%s%s" CR), mqtt_topic, gateway_name, subjectMQTTtoPilight);
+
+ initCC1101();
-# ifdef ZradioCC1101
- ELECHOUSE_cc1101.Init();
- ELECHOUSE_cc1101.SetRx(receiveMhz); // set Receive on
-# endif
rf.setCallback(pilightCallback);
# ifdef Pilight_rawEnabled
if (pilightRawEnabled) {
@@ -353,5 +308,6 @@ extern void enablePilightReceive() {
pinMode(RF_EMITTER_GPIO, OUTPUT); // Set this here, because if this is the RX pin it was reset to INPUT by Serial.end();
rf.enableReceiver();
loadPilightConfig();
+ Log.trace(F("ZgatewayPilight setup done " CR));
};
#endif
diff --git a/main/ZgatewayRF.ino b/main/ZgatewayRF.ino
index c7c3dd417a..5bea8ea02b 100644
--- a/main/ZgatewayRF.ino
+++ b/main/ZgatewayRF.ino
@@ -106,31 +106,6 @@ void RFtoMQTTdiscovery(SIGNAL_SIZE_UL_ULL MQTTvalue) {
}
# endif
-void setupRF() {
- //RF init parameters
- Log.notice(F("RF_EMITTER_GPIO: %d " CR), RF_EMITTER_GPIO);
- Log.notice(F("RF_RECEIVER_GPIO: %d " CR), RF_RECEIVER_GPIO);
-# ifdef ZradioCC1101 //receiving with CC1101
- if (ELECHOUSE_cc1101.getCC1101()) {
- Log.notice(F("C1101 spi Connection OK" CR));
- } else {
- Log.error(F("C1101 spi Connection Error" CR));
- }
-
- ELECHOUSE_cc1101.Init();
- ELECHOUSE_cc1101.SetRx(receiveMhz);
-# endif
-# ifdef RF_DISABLE_TRANSMIT
- mySwitch.disableTransmit();
-# else
- mySwitch.enableTransmit(RF_EMITTER_GPIO);
-# endif
- mySwitch.setRepeatTransmit(RF_EMITTER_REPEAT);
- mySwitch.enableReceive(RF_RECEIVER_GPIO);
- Log.trace(F("ZgatewayRF command topic: %s%s%s" CR), mqtt_topic, gateway_name, subjectMQTTtoRF);
- Log.trace(F("ZgatewayRF setup done" CR));
-}
-
void RFtoMQTT() {
if (mySwitch.available()) {
StaticJsonDocument RFdataBuffer;
@@ -161,7 +136,7 @@ void RFtoMQTT() {
RFdata["raw"] = rawDump;
# endif
# ifdef ZradioCC1101 // set Receive off and Transmitt on
- RFdata["mhz"] = receiveMhz;
+ RFdata["frequency"] = RFConfig.frequency;
# endif
mySwitch.resetAvailable();
@@ -187,9 +162,9 @@ void RFtoMQTT() {
# if simpleReceiving
void MQTTtoRF(char* topicOri, char* datacallback) {
# ifdef ZradioCC1101 // set Receive off and Transmitt on
- disableActiveReceiver();
- ELECHOUSE_cc1101.SetTx(receiveMhz);
- Log.notice(F("Transmit mhz: %F" CR), receiveMhz);
+ disableCurrentReceiver();
+ ELECHOUSE_cc1101.SetTx(RFConfig.frequency);
+ Log.notice(F("Transmit mhz: %F" CR), RFConfig.frequency);
# endif
mySwitch.disableReceive();
mySwitch.enableTransmit(RF_EMITTER_GPIO);
@@ -241,7 +216,7 @@ void MQTTtoRF(char* topicOri, char* datacallback) {
pub(subjectGTWRFtoMQTT, datacallback); // we acknowledge the sending by publishing the value to an acknowledgement topic, for the moment even if it is a signal repetition we acknowledge also
}
# ifdef ZradioCC1101 // set Receive on and Transmitt off
- ELECHOUSE_cc1101.SetRx(receiveMhz);
+ ELECHOUSE_cc1101.SetRx(RFConfig.frequency);
mySwitch.disableTransmit();
mySwitch.enableReceive(RF_RECEIVER_GPIO);
# endif
@@ -262,13 +237,13 @@ void MQTTtoRF(char* topicOri, JsonObject& RFdata) { // json object decoding
Log.notice(F("RF Pulse Lgth: %d" CR), valuePLSL);
Log.notice(F("Bits nb: %d" CR), valueBITS);
# ifdef ZradioCC1101 // set Receive off and Transmitt on
- disableActiveReceiver();
+ disableCurrentReceiver();
int txPower = RFdata["txpower"] | RF_CC1101_TXPOWER;
ELECHOUSE_cc1101.setPA((int)txPower);
Log.notice(F("CC1101 TX Power: %d" CR), txPower);
- float trMhz = RFdata["mhz"] | CC1101_FREQUENCY;
+ float trMhz = RFdata["mhz"] | RF_FREQUENCY;
if (validFrequency((int)trMhz)) {
ELECHOUSE_cc1101.SetTx(trMhz);
Log.notice(F("Transmit mhz: %F" CR), trMhz);
@@ -283,32 +258,9 @@ void MQTTtoRF(char* topicOri, JsonObject& RFdata) { // json object decoding
// we acknowledge the sending by publishing the value to an acknowledgement topic, for the moment even if it is a signal repetition we acknowledge also
pub(subjectGTWRFtoMQTT, RFdata);
mySwitch.setRepeatTransmit(RF_EMITTER_REPEAT); // Restore the default value
- } else {
- bool success = false;
- if (RFdata.containsKey("active")) {
- Log.trace(F("RF active:" CR));
- activeReceiver = ACTIVE_RF;
- success = true;
- }
-# ifdef ZradioCC1101 // set Receive on and Transmitt off
- float tempMhz = RFdata["mhz"];
- if (RFdata.containsKey("mhz") && validFrequency(tempMhz)) {
- receiveMhz = tempMhz;
- Log.notice(F("Receive mhz: %F" CR), receiveMhz);
- success = true;
- }
-# endif
- if (success) {
- // we acknowledge the sending by publishing the value to an acknowledgement topic, for the moment even if it is a signal repetition we acknowledge also
- pub(subjectGTWRFtoMQTT, RFdata);
- } else {
-# ifndef ARDUINO_AVR_UNO // Space issues with the UNO
- pub(subjectGTWRFtoMQTT, "{\"Status\": \"Error\"}"); // Fail feedback
-# endif
- Log.error(F("MQTTtoRF Fail json" CR));
- }
}
- enableActiveReceiver(false);
+
+ enableActiveReceiver();
}
}
# endif
@@ -317,36 +269,24 @@ int receiveInterupt = -1;
void disableRFReceive() {
Log.trace(F("disableRFReceive %d" CR), receiveInterupt);
- if (receiveInterupt != -1) {
- receiveInterupt = -1;
- mySwitch.disableReceive();
- }
+ mySwitch.disableReceive();
}
void enableRFReceive() {
-# ifdef ZradioCC1101
- Log.notice(F("Switching to RF Receiver: %F" CR), receiveMhz);
-# else
- Log.notice(F("Switching to RF Receiver" CR));
-# endif
-# ifndef ARDUINO_AVR_UNO // Space issues with the UNO
-# ifdef ZgatewayPilight
- disablePilightReceive();
-# endif
-# ifdef ZgatewayRTL_433
- disableRTLreceive();
-# endif
-# endif
-# ifdef ZgatewayRF2
- disableRF2Receive();
-# endif
+ Log.notice(F("Enable RF Receiver: %FMhz" CR), RFConfig.frequency);
+ //RF init parameters
+ Log.notice(F("RF_EMITTER_GPIO: %d " CR), RF_EMITTER_GPIO);
+ Log.notice(F("RF_RECEIVER_GPIO: %d " CR), RF_RECEIVER_GPIO);
-# ifdef ZradioCC1101 // set Receive on and Transmitt off
- ELECHOUSE_cc1101.Init();
- ELECHOUSE_cc1101.SetRx(receiveMhz);
-# endif
+# ifdef RF_DISABLE_TRANSMIT
mySwitch.disableTransmit();
+# else
+ mySwitch.enableTransmit(RF_EMITTER_GPIO);
+# endif
receiveInterupt = RF_RECEIVER_GPIO;
- mySwitch.enableReceive(RF_RECEIVER_GPIO);
+ mySwitch.setRepeatTransmit(RF_EMITTER_REPEAT);
+ mySwitch.enableReceive(receiveInterupt);
+ Log.trace(F("ZgatewayRF command topic: %s%s%s" CR), mqtt_topic, gateway_name, subjectMQTTtoRF);
+ Log.trace(F("ZgatewayRF setup done" CR));
}
#endif
diff --git a/main/ZgatewayRF2.ino b/main/ZgatewayRF2.ino
index f10b78fad7..e592dd7893 100644
--- a/main/ZgatewayRF2.ino
+++ b/main/ZgatewayRF2.ino
@@ -55,21 +55,6 @@ struct RF2rxd {
RF2rxd rf2rd;
-void setupRF2() {
-# ifdef ZradioCC1101 //receiving with CC1101
- ELECHOUSE_cc1101.Init();
- ELECHOUSE_cc1101.setMHZ(receiveMhz);
- ELECHOUSE_cc1101.SetRx(receiveMhz);
-# endif
- NewRemoteReceiver::init(RF_RECEIVER_GPIO, 2, rf2Callback);
- Log.notice(F("RF_EMITTER_GPIO: %d " CR), RF_EMITTER_GPIO);
- Log.notice(F("RF_RECEIVER_GPIO: %d " CR), RF_RECEIVER_GPIO);
- Log.trace(F("ZgatewayRF2 command topic: %s%s%s" CR), mqtt_topic, gateway_name, subjectMQTTtoRF2);
- Log.trace(F("ZgatewayRF2 setup done " CR));
- pinMode(RF_EMITTER_GPIO, OUTPUT);
- digitalWrite(RF_EMITTER_GPIO, LOW);
-}
-
# ifdef ZmqttDiscovery
//Register for autodiscover in Home Assistant
void RF2toMQTTdiscovery(JsonObject& data) {
@@ -148,13 +133,9 @@ void rf2Callback(unsigned int period, unsigned long address, unsigned long group
# if simpleReceiving
void MQTTtoRF2(char* topicOri, char* datacallback) {
-# ifdef ZradioCC1101
NewRemoteReceiver::disable();
- disableActiveReceiver();
- ELECHOUSE_cc1101.Init();
pinMode(RF_EMITTER_GPIO, OUTPUT);
- ELECHOUSE_cc1101.SetTx(CC1101_FREQUENCY); // set Transmit on
-# endif
+ initCC1101();
// RF DATA ANALYSIS
//We look into the subject to see if a special RF protocol is defined
@@ -253,7 +234,7 @@ void MQTTtoRF2(char* topicOri, char* datacallback) {
}
}
# ifdef ZradioCC1101
- ELECHOUSE_cc1101.SetRx(receiveMhz); // set Receive on
+ ELECHOUSE_cc1101.SetRx(RFConfig.frequency); // set Receive on
NewRemoteReceiver::enable();
# endif
}
@@ -267,13 +248,9 @@ void MQTTtoRF2(char* topicOri, JsonObject& RF2data) { // json object decoding
int boolSWITCHTYPE = RF2data["switchType"] | 99;
bool success = false;
if (boolSWITCHTYPE != 99) {
-# ifdef ZradioCC1101
NewRemoteReceiver::disable();
- disableActiveReceiver();
- ELECHOUSE_cc1101.Init();
pinMode(RF_EMITTER_GPIO, OUTPUT);
- ELECHOUSE_cc1101.SetTx(CC1101_FREQUENCY); // set Transmit on
-# endif
+ initCC1101();
Log.trace(F("MQTTtoRF2 switch type ok" CR));
bool isDimCommand = boolSWITCHTYPE == 2;
unsigned long valueCODE = RF2data["address"];
@@ -311,19 +288,6 @@ void MQTTtoRF2(char* topicOri, JsonObject& RF2data) { // json object decoding
success = true;
}
}
- if (RF2data.containsKey("active")) {
- Log.trace(F("RF2 active:" CR));
- activeReceiver = ACTIVE_RF2;
- success = true;
- }
-# ifdef ZradioCC1101 // set Receive on and Transmitt off
- float tempMhz = RF2data["mhz"];
- if (RF2data.containsKey("mhz") && validFrequency(tempMhz)) {
- receiveMhz = tempMhz;
- Log.notice(F("Receive mhz: %F" CR), receiveMhz);
- success = true;
- }
-# endif
if (success) {
// we acknowledge the sending by publishing the value to an acknowledgement topic, for the moment even if it is a signal repetition we acknowledge also
pub(subjectRF2toMQTT, RF2data);
@@ -333,39 +297,26 @@ void MQTTtoRF2(char* topicOri, JsonObject& RF2data) { // json object decoding
# endif
Log.error(F("MQTTtoRF2 failed json read" CR));
}
- enableActiveReceiver(false);
+ enableActiveReceiver();
}
}
# endif
void disableRF2Receive() {
Log.trace(F("disableRF2Receive" CR));
- NewRemoteReceiver::deinit();
- NewRemoteReceiver::init(-1, 2, rf2Callback); // mark _interupt with -1
- NewRemoteReceiver::deinit();
+ NewRemoteReceiver::disable();
}
void enableRF2Receive() {
-# ifdef ZradioCC1101
- Log.notice(F("Switching to RF2 Receiver: %F" CR), receiveMhz);
-# else
- Log.notice(F("Switching to RF2 Receiver" CR));
-# endif
-# ifdef ZgatewayPilight
- disablePilightReceive();
-# endif
-# ifdef ZgatewayRTL_433
- disableRTLreceive();
-# endif
-# ifdef ZgatewayRF
- disableRFReceive();
-# endif
-
-# ifdef ZradioCC1101
- ELECHOUSE_cc1101.Init();
- ELECHOUSE_cc1101.SetRx(receiveMhz); // set Receive on
-# endif
+ Log.trace(F("enableRF2Receive" CR));
NewRemoteReceiver::init(RF_RECEIVER_GPIO, 2, rf2Callback);
+
+ Log.notice(F("RF_EMITTER_GPIO: %d " CR), RF_EMITTER_GPIO);
+ Log.notice(F("RF_RECEIVER_GPIO: %d " CR), RF_RECEIVER_GPIO);
+ Log.trace(F("ZgatewayRF2 command topic: %s%s%s" CR), mqtt_topic, gateway_name, subjectMQTTtoRF2);
+ pinMode(RF_EMITTER_GPIO, OUTPUT);
+ digitalWrite(RF_EMITTER_GPIO, LOW);
+ Log.trace(F("ZgatewayRF2 setup done " CR));
}
#endif
diff --git a/main/ZgatewayRTL_433.ino b/main/ZgatewayRTL_433.ino
index 9108741f9e..bd87e72e19 100644
--- a/main/ZgatewayRTL_433.ino
+++ b/main/ZgatewayRTL_433.ino
@@ -40,8 +40,6 @@
char messageBuffer[JSON_MSG_BUFFER];
-rtl_433_ESP rtl_433;
-
# ifdef ZmqttDiscovery
SemaphoreHandle_t semaphorecreateOrUpdateDeviceRTL_433;
std::vector RTL_433devices;
@@ -273,7 +271,7 @@ void setupRTL_433() {
semaphorecreateOrUpdateDeviceRTL_433 = xSemaphoreCreateBinary();
xSemaphoreGive(semaphorecreateOrUpdateDeviceRTL_433);
# endif
- Log.trace(F("ZgatewayRTL_433 command topic: %s%s%s" CR), mqtt_topic, gateway_name, subjectMQTTtoRTL_433);
+ Log.trace(F("ZgatewayRTL_433 command topic: %s%s%s" CR), mqtt_topic, gateway_name, subjectMQTTtoRFset);
Log.notice(F("ZgatewayRTL_433 setup done " CR));
}
@@ -281,69 +279,9 @@ void RTL_433Loop() {
rtl_433.loop();
}
-extern void MQTTtoRTL_433(char* topicOri, JsonObject& RTLdata) {
- if (cmpToMainTopic(topicOri, subjectMQTTtoRTL_433)) {
- float tempMhz = RTLdata["mhz"];
- bool success = false;
- if (RTLdata.containsKey("mhz") && validFrequency(tempMhz)) {
- receiveMhz = tempMhz;
- Log.notice(F("RTL_433 Receive mhz: %F" CR), receiveMhz);
- success = true;
- }
- if (RTLdata.containsKey("active")) {
- Log.trace(F("RTL_433 active:" CR));
- activeReceiver = ACTIVE_RTL; // Enable RTL_433 gateway
- success = true;
- }
- if (RTLdata.containsKey("rssi")) {
- int rssiThreshold = RTLdata["rssi"] | 0;
- Log.notice(F("RTL_433 RSSI Threshold Delta: %d " CR), rssiThreshold);
- rtl_433.setRSSIThreshold(rssiThreshold);
- success = true;
- }
-# if defined(RF_SX1276) || defined(RF_SX1278)
- if (RTLdata.containsKey("ookThreshold")) {
- int newOokThreshold = RTLdata["ookThreshold"] | 0;
- Log.notice(F("RTL_433 ookThreshold %d" CR), newOokThreshold);
- rtl_433.setOOKThreshold(newOokThreshold);
- success = true;
- }
-# endif
- if (RTLdata.containsKey("debug")) {
- int debug = RTLdata["debug"] | -1;
- Log.notice(F("RTL_433 set debug: %d" CR), debug);
- // rtl_433.setDebug(debug);
- rtl_433.initReceiver(RF_MODULE_RECEIVER_GPIO, receiveMhz);
- success = true;
- }
- if (RTLdata.containsKey("status")) {
- Log.notice(F("RTL_433 get status:" CR));
- rtl_433.getStatus();
- success = true;
- }
- if (success) {
- pub(subjectRTL_433toMQTT, RTLdata);
- } else {
- pub(subjectRTL_433toMQTT, "{\"Status\": \"Error\"}"); // Fail feedback
- Log.error(F("[rtl_433] MQTTtoRTL_433 Fail json" CR));
- }
- enableActiveReceiver(false);
- }
-}
-
extern void enableRTLreceive() {
- Log.notice(F("Switching to RTL_433 Receiver: %FMhz" CR), receiveMhz);
-# ifdef ZgatewayRF
- disableRFReceive();
-# endif
-# ifdef ZgatewayRF2
- disableRF2Receive();
-# endif
-# ifdef ZgatewayPilight
- disablePilightReceive();
-# endif
-
- rtl_433.initReceiver(RF_MODULE_RECEIVER_GPIO, receiveMhz);
+ Log.notice(F("Enable RTL_433 Receiver: %FMhz" CR), RFConfig.frequency);
+ rtl_433.initReceiver(RF_MODULE_RECEIVER_GPIO, RFConfig.frequency);
rtl_433.enableReceiver();
}
diff --git a/main/ZwebUI.ino b/main/ZwebUI.ino
index 3a93ca30e5..bd2bcbb7df 100644
--- a/main/ZwebUI.ino
+++ b/main/ZwebUI.ino
@@ -947,54 +947,72 @@ void handleLA() {
if (server.hasArg("save")) {
StaticJsonDocument jsonBuffer;
JsonObject WEBtoLORA = jsonBuffer.to();
-
+ bool update = false;
if (server.hasArg("lf")) {
WEBtoLORA["frequency"] = server.arg("lf");
+ update = true;
}
if (server.hasArg("lt")) {
WEBtoLORA["txpower"] = server.arg("lt");
+ update = true;
}
if (server.hasArg("ls")) {
WEBtoLORA["spreadingfactor"] = server.arg("ls");
+ update = true;
}
if (server.hasArg("lb")) {
WEBtoLORA["signalbandwidth"] = server.arg("lb");
+ update = true;
}
if (server.hasArg("lc")) {
WEBtoLORA["codingrate"] = server.arg("lc");
+ update = true;
}
if (server.hasArg("ll")) {
WEBtoLORA["preamblelength"] = server.arg("ll");
+ update = true;
}
if (server.hasArg("lw")) {
WEBtoLORA["syncword"] = server.arg("lw");
+ update = true;
}
if (server.hasArg("lr")) {
WEBtoLORA["enablecrc"] = server.arg("lr");
+ update = true;
} else {
WEBtoLORA["enablecrc"] = false;
+ update = true;
}
if (server.hasArg("li")) {
WEBtoLORA["invertiq"] = server.arg("li");
+ update = true;
} else {
WEBtoLORA["invertiq"] = false;
+ update = true;
}
if (server.hasArg("ok")) {
WEBtoLORA["onlyknown"] = server.arg("ok");
+ update = true;
} else {
WEBtoLORA["onlyknown"] = false;
+ update = true;
+ }
+ if (update) {
+ Log.notice(F("[WebUI] Save data" CR));
+ WEBtoLORA["save"] = true;
+ LORAConfig_fromJson(WEBtoLORA);
+ stateLORAMeasures();
+ Log.trace(F("[WebUI] LORAConfig end" CR));
}
-
- LORAConfig_fromJson(WEBtoLORA);
}
}
char jsonChar[100];
@@ -1056,8 +1074,121 @@ void handleLA() {
snprintf(buffer, WEB_TEMPLATE_BUFFER_MAX_SIZE, footer, OMG_VERSION);
response += String(buffer);
server.send(200, "text/html", response);
- stateLORAMeasures();
- Log.trace(F("[WebUI] LORAConfig end" CR));
+}
+# elif defined(ZgatewayRTL_433) || defined(ZgatewayPiLight) || defined(ZgatewayRF) || defined(ZgatewayRF2) || defined(ZactuatorSomfy)
+# include