New complication #778

kcossabo · 2023-05-04T01:02:39Z

kcossabo
May 4, 2023

Well, I upgraded, and bad things...

Home Assistant 2023.5.0
Supervisor 2023.04.1
Operating System 10.1
Frontend 20230503.1 - latest
Blueprint Version: v.3.2.2
Firmware: 2023.4.4 (May 3 2023, 19:52:59)
logs_nspanelone_logs (1).txt

The panel is on the HA blue screen, with IP address correct,TFT 3.2.2, ESPHome 3.3, Blueprint (Blank)
Does not leave that screen. So far I have

powered on and off
ESPHome was showing an upgrade, so I upgraded
Integrations -> ESPHome -> Update TFT display (It updated)

How do I troubleshoot?

Herbert69-Cyber · 2023-05-04T06:16:49Z

Herbert69-Cyber
May 4, 2023

Same problem here, bit like the Microsoft famous blue screen of death. I think it was the ESphome update 2 days ago that broke it. Waiting patiently for a fix.

1 reply

Herbert69-Cyber May 4, 2023

Sorry just found fix documented in issues log

edwardtfn · 2023-05-04T06:55:05Z

edwardtfn
May 4, 2023
Collaborator

The panel is on the HA blue screen, with IP address correct,TFT 3.2.2, ESPHome 3.3, Blueprint (Blank)

The problem here is that with the update of your ESPHome, it recompile each of your devices and for your panel that means getting the latest code from GitHub, which is now v3.3, but it wasn't the same for the other parts (TFT file and the Blueprint), so you have a version mismatch which will cause your panel to be stuck in the boot page (the blue screen) or on "Loading...".

You can fix that by updating the TFT file and the Blueprint also to v3.3, so they will have the same version as your ESPHome.

There are some update procedures on wiki, but please let me know if you get stuck on that process and I will try to help:
https://github.com/Blackymas/NSPanel_HA_Blueprint/wiki/(EN)-HowTo---All-important-thing-you-should-know#2-update-blueprint

5 replies

kcossabo May 4, 2023
Author

Thank You - still working the issue but closer. I added the above to the tips needed.

Current situation;

Downloaded new blueprint
Rebooted HA

change date on config -> no change
Power on and off -> no change

Updated TFT Display

Panel shows downloading
completes, does check
completes
reboots

Sent a Reset from Settings --> Devices & Services --> Integrations

TFT: 3.2.2
ESPHome 3.3
BluePrint 3.3

Went to ESP Home tab, and update all
Then the panel, install wirelessly

Sent a Reset from Settings --> Devices & Services --> Integrations

change date on config -> no change
Power on and off ->
logs_update-all.txt

logs_nspanelone_run.txt
no change

kcossabo May 4, 2023
Author

ESPHome Log
5c53de3b_esphome_2023-05-04T13-02-58.251Z.log

edwardtfn May 4, 2023
Collaborator

You have to update TFT to v3.3.

Download the file from GitHub:

Then upload it to your local www server in Home Assistant using the File Editor (browse to the folder www, delete the old TFT from there and then upload the new one).
Then go to your device page (Settings > Devices and Services > ESPHome) and press Upload TFT.

https://github.com/Blackymas/NSPanel_HA_Blueprint/wiki/(EN)-HowTo---All-important-thing-you-should-know#4-update-tft

kcossabo May 4, 2023
Author

Cool, did not read to download the new version, and the versions looked like they were 2 weeks old. so I left it like it is.

I cloned (this morning) the git repository to the Pi, but the link above

https://github.com/Blackymas/NSPanel_HA_Blueprint/raw/main/nspanel_us.tft

is not in my clone.... no /raw/...

anyways, did the download, now up and running. On boot screen;

TFT: 3.3
ESPHome 3.3
BluePrint 3.3

Also two new icons in the upper left, a 1 and a 2 in a box?

Thank You

Do I have this correct?

Process;

download and update Blueprint
download and update TFT file (not sure where this is for each release)
go to the ESPHome Tab, Update all, then update the panel

edwardtfn May 4, 2023
Collaborator

Also two new icons in the upper left, a 1 and a 2 in a box?

That shows physical relays 1 and 2 are on.

Herbert69-Cyber · 2023-05-04T09:04:58Z

Herbert69-Cyber
May 4, 2023

Thank you, I have updated TFT: 3.3 and ESPHome: 3.3 and the Blueprint to 3.3 but it is still stuck on the boot screen As far as I can see all three are the same version, even the relay switches no longer work even on fullback. I'm using the US Version by the way. Clinton

…

On Thu, May 4, 2023 at 6:55 PM Edward Firmo ***@***.***> wrote: The panel is on the HA blue screen, with IP address correct,TFT 3.2.2, ESPHome 3.3, Blueprint (Blank) The problem here is that with the update of your ESPHome, it recompile each of your devices and for your panel that means getting the latest code from GitHub, which is now v3.3, but it wasn't the same for the other parts (TFT file and the Blueprint), so you have a version mismatch which will cause your panel to be stuck in the boot page (the blue screen) or on "Loading...". You can fix that by updating the TFT file and the Blueprint also to v3.3, so they will have the same version as your ESPHome. There are some update procedures on wiki, but please let me know if you get stuck on that process and I will try to help: https://github.com/Blackymas/NSPanel_HA_Blueprint/wiki/(EN)-HowTo---All-important-thing-you-should-know#2-update-blueprint — Reply to this email directly, view it on GitHub <#778 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AV4SDXCQWJVQERZ6IZL7ACDXENHFJANCNFSM6AAAAAAXVDXKDE> . You are receiving this because you commented.Message ID: <Blackymas/NSPanel_HA_Blueprint/repo-discussions/778/comments/5801505@ github.com>

1 reply

edwardtfn May 4, 2023
Collaborator

I have updated TFT: 3.3 and ESPHome: 3.3 and the Blueprint to 3.3 but it is
still stuck on the boot screen

Can you see in the boot page the version of all 3 parts (TFT, ESPHome and Blueprint)? I wanna know if all parts have reported it's new versions to the panel.
By the way, what if you press the reboot button on that screen?
Any error message on your Home Assistant logs? (Settings > System > Logs)

Herbert69-Cyber · 2023-05-04T09:23:52Z

Herbert69-Cyber
May 4, 2023

Blueprint is blank, TFT and ESphome is populated with 3.3. Get this event error, but that is all Thanks agian [image: image.png]

…

On Thu, May 4, 2023 at 9:19 PM Edward Firmo ***@***.***> wrote: I have updated TFT: 3.3 and ESPHome: 3.3 and the Blueprint to 3.3 but it is still stuck on the boot screen Can you see in the boot page the version of all 3 parts (TFT, ESPHome and Blueprint)? I wanna know if all parts have reported it's new versions to the panel. By the way, what if you press the reboot button on that screen? Any error message on your Home Assistant logs? (Settings > System > Logs) — Reply to this email directly, view it on GitHub <#778 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AV4SDXBQV66WWKS6YNTILSDXENYAXANCNFSM6AAAAAAXVDXKDE> . You are receiving this because you commented.Message ID: <Blackymas/NSPanel_HA_Blueprint/repo-discussions/778/comments/5802766@ github.com>

1 reply

edwardtfn May 4, 2023
Collaborator

I didn't got the image. Could you please share that again?

Also, could you pleas eco firm you can see version 3.3 whe editing settings in your blueprint? And as you get to that screen, please double check if the panel is selected in the first field.

Herbert69-Cyber · 2023-05-04T09:51:08Z

Herbert69-Cyber
May 4, 2023

Yes when I edit the blue print I can see version 3.3. Hopefully screen shot works this time. I suspect my problem is the blueprint, I have 2 panels each attached to a different ESp32 device in HA and I also have 2 automations in HA perhaps some conflict going on. Both devices are stuck on the boot screen Solution might be to delete automations and blueprint and start again. Clinton

…

On Thu, 4 May 2023, 21:32 Edward Firmo, ***@***.***> wrote: I didn't got the image. Could you please share that again? Also, could you pleas eco firm you can see version 3.3 whe editing settings in your blueprint? [image: IMG_6206] <https://user-images.githubusercontent.com/94725493/236166972-cb776c14-4e91-4e68-950c-316261580b3e.jpeg> — Reply to this email directly, view it on GitHub <#778 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AV4SDXE4HWDTWLGHPT2D2DDXENZUNANCNFSM6AAAAAAXVDXKDE> . You are receiving this because you commented.Message ID: <Blackymas/NSPanel_HA_Blueprint/repo-discussions/778/comments/5802876@ github.com>

1 reply

edwardtfn May 4, 2023
Collaborator

Hopefully screen shot works this time.

Unfortunately still no image. I belive it won't work when you send via email.

I suspect my problem is the blueprint, I have 2 panels each attached to a
different ESp32 device in HA and I also have 2 automations in HA perhaps
some conflict going on. Both devices are stuck on the boot screen

It could be the Blueprint. It's hard to say with the info I have so far.
Having multiple panels shouldn't be a problem. I have 3 panels at home, both US and EU models, and they are all working fine.

Solution might be to delete automations and blueprint and start again.

That's always n efficient way to fix issues, but a bit radical. But if that is easy for you to try, why not? 🙂

Herbert69-Cyber · 2023-05-04T10:18:39Z

Herbert69-Cyber
May 4, 2023

Here is the error message plain txt from an hour ago when I tried to reboot to {"panspanel NSPanel event changed to {"page": "boot", "component": "currentpage", "value": "pagechange"} Off to bed now its 10:20pm in New Zealand, tackle again tomorrow Clinton ge": "boot", "component": "currentpage", "value": "pagechange"} On Thu, May 4, 2023 at 9:50 PM Clinton Gallie ***@***.***> wrote:

…

Yes when I edit the blue print I can see version 3.3. Hopefully screen shot works this time. I suspect my problem is the blueprint, I have 2 panels each attached to a different ESp32 device in HA and I also have 2 automations in HA perhaps some conflict going on. Both devices are stuck on the boot screen Solution might be to delete automations and blueprint and start again. Clinton On Thu, 4 May 2023, 21:32 Edward Firmo, ***@***.***> wrote: > I didn't got the image. Could you please share that again? > > Also, could you pleas eco firm you can see version 3.3 whe editing > settings in your blueprint? > [image: IMG_6206] > <https://user-images.githubusercontent.com/94725493/236166972-cb776c14-4e91-4e68-950c-316261580b3e.jpeg> > > — > Reply to this email directly, view it on GitHub > <#778 (reply in thread)>, > or unsubscribe > <https://github.com/notifications/unsubscribe-auth/AV4SDXE4HWDTWLGHPT2D2DDXENZUNANCNFSM6AAAAAAXVDXKDE> > . > You are receiving this because you commented.Message ID: > <Blackymas/NSPanel_HA_Blueprint/repo-discussions/778/comments/5802876@ > github.com> >

8 replies

Herbert69-Cyber May 5, 2023

Maybe this is it, found these entries in the log

edwardtfn May 5, 2023
Collaborator

Well, the first Al last messages are related to some communication problem with your panel, but I think the main issue is in the message in the middle, saying you have 2 automations with the same id. You will have to remove one of those or at least change its ID (but then make sure you don't have 2 automations assigned to the same panel).

Herbert69-Cyber May 5, 2023

Had to delete my automatons and the blueprint and reload but got there thanks to your hint. On the bright side I have the weekend to reconfigure my switches :-)

Herbert69-Cyber May 5, 2023

P.s its not actually raining at the moment lol

edwardtfn May 5, 2023
Collaborator

This info comes from your weather integration.

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

New complication #778

{{title}}

{{editor}}'s edit

{{editor}}'s edit

Replies: 6 comments 17 replies

{{title}}

{{title}}

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

Select a reply

New complication #778

Replies: 6 comments · 17 replies

edwardtfn May 4, 2023 Collaborator

kcossabo May 4, 2023 Author

kcossabo May 4, 2023 Author

edwardtfn May 4, 2023 Collaborator

kcossabo May 4, 2023 Author

Thank You

edwardtfn May 4, 2023 Collaborator

edwardtfn May 4, 2023 Collaborator

edwardtfn May 4, 2023 Collaborator

edwardtfn May 4, 2023 Collaborator

edwardtfn May 5, 2023 Collaborator

edwardtfn May 5, 2023 Collaborator

Replies: 6 comments 17 replies

edwardtfn
May 4, 2023
Collaborator

kcossabo May 4, 2023
Author

kcossabo May 4, 2023
Author

edwardtfn May 4, 2023
Collaborator

kcossabo May 4, 2023
Author

edwardtfn May 4, 2023
Collaborator

edwardtfn May 4, 2023
Collaborator

edwardtfn May 4, 2023
Collaborator

edwardtfn May 4, 2023
Collaborator

edwardtfn May 5, 2023
Collaborator

edwardtfn May 5, 2023
Collaborator