From 61011df703c440180159ef0a91bce1ac9535cf95 Mon Sep 17 00:00:00 2001 From: Zengrui <60548873+Zengruiray@users.noreply.github.com> Date: Thu, 29 Sep 2022 23:45:35 +0800 Subject: [PATCH] Update usb_setup.md MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit 更新了usb_setup.md的中文翻译 --- development/hardware/usb_setup.md | 70 ++++++++++++++++++++----------- 1 file changed, 46 insertions(+), 24 deletions(-) diff --git a/development/hardware/usb_setup.md b/development/hardware/usb_setup.md index d8f8da3c..7d68d733 100644 --- a/development/hardware/usb_setup.md +++ b/development/hardware/usb_setup.md @@ -1,54 +1,66 @@ -# Install Fuchsia from a USB flash drive + +# 从 USB 闪存驱动器安装Fuchsia -You can use a USB flash drive to make your target device to boot from + +您可以使用 USB 闪存驱动器使您的目标设备从 Fuchsia 安装程序启动，然后直接从 USB 将新构建的 Fuchsia 映像安装到设备上。 -To prepare a USB flash drive to be a bootable disk, do the following: + +要将 USB 闪存驱动器准备为可引导磁盘，请执行以下操作： -1. Set the build configuration to `workstation_eng.x64` and include - the recovery package (`recovery-installer`): + +1. 请将构建配置设置为 workstation_eng.x64 并包含恢复安装包(`recovery-installer`)： ```posix-terminal fx set workstation_eng.x64 --with //build/images/recovery:recovery-installer ``` -1. Build a new Fuchsia image and its artifacts: + +1. 请构建一个新的 Fuchsia 映像及其源代码的生成物（artifacts）： ```posix-terminal fx build ``` -1. Plug a USB flash drive into your workstation. + +1. 请将 USB 闪存驱动器插入您的工作站。 -1. Identify the path to the USB drive: + +1. 确定 USB 驱动器的文件路径： ```posix-terminal fx list-usb-disks ``` - This command prints output similar to the following: + + 然后请用此命令打印出类似于以下内容的输出： ``` none {:.devsite-disable-click-to-copy} $ fx list-usb-disks /dev/sda - My Example USB Disk ``` -1. Create a bootable USB drive: + +1. 请创建一个可启动的 USB 驱动器： ```posix-terminal fx mkinstaller -v --new-installer {{ "" }}PATH_TO_USB_DRIVE{{ ""}} ``` - Replace `PATH_TO_USB_DRIVE` with the path to the USB drive from the step above. + + 请将 `PATH_TO_USB_DRIVE` 替换为上述步骤中. - The example command below selects the `/dev/sda` path: + + 请在下面的示例命令中选择 `/dev/sda` 路径： ``` none {:.devsite-disable-click-to-copy} $ fx mkinstaller -v --new-installer /dev/sda ``` - When finished, the command prints output similar to the following in the end: + + 完成后，该命令最后会打印出类似于以下内容的输出： ``` none {:.devsite-disable-click-to-copy} @@ -62,22 +74,32 @@ To prepare a USB flash drive to be a bootable disk, do the following: mkinstaller: INFO: Ejected USB disk ``` -1. Unplug the USB drive from the workstation. + +1. 请从工作站上拔下 USB 驱动器。 -1. Plug the bootable USB drive into your target device. + +1. 请将可启动 USB 驱动器插入目标设备。 -1. Configure the target device's BIOS to boot from a USB drive. + +1. 请将目标设备的 BIOS 配置为从 USB 驱动器启动。 -1. Reboot the target device. + +1. 请重新启动目标设备。 - The device boots into the Fuchsia Workstation Installer. + + 设备启动到 Fuchsia Workstation 安装程序。 -1. Press **Enter** on prompts to continue the installation process. + +1. 请在出现提示时按 **Enter** 以继续安装过程。 - When the installation is finished, the screen displays `Success! Please restart your computer.` + + 在安装完成后，屏幕显示`Success! Please restart your computer.` -1. Unplug the USB drive from the target device. + +1. 请从目标设备上拔下 USB 驱动器。 -1. Reboot the target device. + +1. 请重新启动目标设备。 - The target device is now booted into Fuchsia’s Workstation. + + 随后目标设备现在启动到 Fuchsia 的工作站（Workstation）。