Any available units?

[MaikaiLife]

Before I go and purchase all the equipment to create these devices, I'd like to see if anyone has 8 of these. I have 8x LCN097HV4 indoor cassettes that I need to be able to remote control.

Please let me know if you have some of these available and what you would want for them.

Thank you!

[MaikaiLife]

@pinhao @katshup @florianbrede-ayet @JanM321

I've gone ahead and purchased some units, but I'm wondering since the LMCN077HV is on the list of supported devices if anyone could drop me a picture of what the connection looks like on the indoor unit so I know if I should get some sort of connectors such as the JST connectors?

[ExquisiteMetropolis]

How did you mange to order them? I'm looking for 2 of these.

[MaikaiLife]

I ordered them through JLCPB using these instructions.

https://docs.easyeda.com/en/PCB/Order-PCB/

One of the parts wasn't available so we had to swap out a part.

[MaikaiLife]

This was the part I had to find an alternative.

[ExquisiteMetropolis]

Thank you so much! I've been able to order it!
Once delivered (probably jan 2025 due to holidays) I will only have use for 3 of the (minimum 5 order).
If anyone is interested in a unit, let me know. (Use 2, keep 1 as spare, 2 for sale).

Next step for me is to find the ESP controller & cable. Any pictures of how the cable is connected to the LG AC in the end?

[MaikaiLife]

I can tell you on my ceiling cartridges they have this little yellow connection block. My plan is to connect right into that block with these connected to the boards. https://www.amazon.com/dp/B0D4M6MTFT?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

[ExquisiteMetropolis]

Mine looks like this. Not sure where to plug the cable. The Amazon link you provided, I can't find the same thing in my area. Only cables with a plug on one end and loose wires on the other. I'm not into soldering or something. Plug & play would be nice. :-)

[ExquisiteMetropolis]

I've received the 5 units.
I'm going to use 2, and keep 1 as spare.
Still waiting on my ESP's and need to figure out on how to connect it to my AC board... (see above) anyone have tip?

If anyone is interested in either of the additional units I have, let me know.
Note tested, no ESP included, no cabling), just the unit itself.
Price: Not looking to make a profit on them. You pay what I paid for a single unit + shipping to whereever you are.

[Scootyb]

If you still have the 2 units i would love to buy them from you.

[ExquisiteMetropolis]

@Scootyb , yes I still have 2 units available. Please provide means of contact (preferably e-mail) and I'll reach out to you.

[KrzysztofHajdamowicz]

how to connect it to my AC board... (see above) anyone have tip?

I bought two set of 3pin JST XH2.54 connector ended with bare wires, like:

Then I soldered both cables, keep middle one connected to middle one and wire 1 to wire 3 and wire 3 to wire 1, in this case:
red -> yellow
black -> black
yellow -> red

[MaikaiLife]

When I ordered my connectors on Amazon, I removed the pins and moved them in the correct order so that all the colors were the same on both sides. In other words, yellow = yellow, red = red, and black = black. Mine had a very small tab you could press down gently with a tiny flathead screwdriver and slide the wire out of the connector to re-arrange them in the correct order.

[robkap]

I also ordered 5 boards from JLCPCB and only need 3.
PM me if you're interested in cost sharing for my 2 extras.