forked from MirageC79/HevORT
-
Notifications
You must be signed in to change notification settings - Fork 0
/
RRF3_D2_config.txt
87 lines (71 loc) · 5.27 KB
/
RRF3_D2_config.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Fri Apr 24 2020 23:53:15 GMT-0600 (MDT)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"HevORT" ; set printer name
M667 S1 ; select CoreXY mode
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes forwards
M569 P5 S0 ; physical drive 5 goes backwards
M569 P6 S0 ; physical drive 6 goes backwards
M584 X0 Y1 Z5:6:2 E3 ; set drive mapping
M671 X-41:207:447 Y20:465:20 S20
M350 X16 Y16 Z16:16:16 E16 I1 ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z800.00:800.00:800.00 E840.00 ; set steps per mm
M566 X1500.00 Y1500.00 Z105.00:105.00:105.00 E900.00 ; set maximum instantaneous speed changes (mm/min)
M203 X30000.00 Y30000.00 Z1200.00:1200.00:1200.00 E10000.00 ; set maximum speeds (mm/min)
M201 X9000.00 Y9000.00 Z120.00:120.00:120.00 E4000.00 ; set accelerations (mm/s^2)
M906 X1150 Y1150 Z1150:1150:1150 E1300 I30 ; set motor currents (mA) and motor idle factor in per cent
M593 F34.2 ; cancel ringing at 34.2Hz
M84 S30 ; Set idle timeout
; Axis Limits
M208 X-9 Y0 Z-20 S1 ; set axis minima
M208 X400 Y400 Z350 S0 ; set axis maxima
;M556 S100 X0 Y0 Z0:0:0 ; set skew x.xxmm on 100mm square x-y obtuse
; Endstops
M574 X1 S0 P"xstop" ; configure active-low endstop for low end on X via pin xstop
M574 Y1 S0 P"ystop" ; configure active-low endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z
; Z-Probe
M307 H3 A-1 C-1 D-1
M950 S0 C"duex.pwm1" ; create servo pin 6 for BLTouch
M558 P9 C"^zprobe.in" B1 H20 F1500 T15000 ; set Z probe type to bltouch, B1 heaters off during probe and the dive height + speeds
G31 P1000 X38.5 Y26 Z1.5 ; set Z probe trigger value, offset and trigger height
M557 X50:390 Y60:420 P20:20 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M307 H0 B0 S0.7 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
; Fans
M950 F0 C"fan0" Q200 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on
; Tools
M563 P0 S"Volcano" D0 H1 F0 ; define tool 0
M572 D0 S0.02 ; set tool 0 pressure advance 0.005
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
M501