| Date: | December 2024 |
|---|---|
| Manual section: | 8 |
| Manual group: | System Manager's Manual |
| Version: |
bluealsad -p PROFILE [OPTION]...
bluealsad is a Linux daemon to give applications access to Bluetooth audio streams using the Bluetooth A2DP, HFP, HSP and/or BLE-MIDI profiles. It provides a D-Bus API to applications, and can be used by ALSA applications via libasound plugins (see bluealsa-plugins(7) for details).
| -h, --help | Output a usage message and exit. |
| -V, --version | Output the version number and exit. |
| -S, --syslog | Send output to system logger (syslogd(8)).
By default, log output is sent to stderr. |
| --loglevel=LEVEL | |
Set the priority level threshold for log messages. Only messages of the given level or higher are logged. The LEVELs are, in decreasing order:
If bluealsad was built with debug enabled, then an additional, lowest, level is available:
If this option is not given then the default is to use the lowest level (i.e., all messages are logged). | |
| -B NAME, --dbus=NAME | |
| BlueALSA D-Bus service name suffix. Without this option, bluealsad registers itself as an "org.bluealsa" D-Bus service. For more information see the EXAMPLES below. | |
| -i hciX, --device=hciX | |
HCI device to use. Can be specified multiple times to select more than one
HCI. Because HCI numbering can change after a system reboot, this option
also accepts HCI MAC address for the hciX value, for example:
Without this option, the default is to use all available HCI devices. | |
| -p NAME, --profile=NAME | |
Enable NAME Bluetooth profile. May be given multiple number of times to enable multiple profiles. It is mandatory to enable at least one Bluetooth profile. For the list of supported profiles see Profiles in the NOTES section below. | |
| -c NAME, --codec=NAME | |
Enable or disable NAME Bluetooth audio codec. May be given multiple number of times to enable (or disable) multiple codecs. In order to disable given audio codec (remove it from the list of audio codecs enabled by default), the NAME has to be prefixed with - (minus) character. It is not possible to disable SBC and CVSD codecs which are mandatory for A2DP and HFP/HSP respectively. By default BlueALSA enables SBC, AAC (if AAC support is compiled-in), CVSD, mSBC (if mSBC support is compiled-in) and LC3-SWB (if LC3-SWB support is compiled-in). For the list of supported audio codecs see the "Available BT audio codecs" section of the bluealsad command-line help message. | |
| --all-codecs | Enable all available Bluetooth audio codecs.
This option is equivalent to enabling all available audio codecs by
specifying them with the After enabling all available codecs, it is still possible to disable some
of them by using the |
| --initial-volume=NUM | |
Set the initial volume to NUM % when a device is first connected. NUM must be an integer in the range from 0 to 100. By default the volume of all PCMs of a device is set to 100% (full volume) when the device is first connected. For some devices, particularly headphones, this can lead to an unpleasant experience. This option allows the user to choose an alternative initial volume level. Only one value can be specified and each device on first connect will have the volume level of all its PCMs set to this value. However, a device with native volume control may then immediately override this level. On subsequent connects the volume will be set to the remembered value from the last disconnection. See Volume control in the NOTES section below for more information. | |
| --keep-alive=SEC | |
Keep Bluetooth transport alive for SEC number of seconds after streaming was closed. This option is required when using bluealsad with applications that
close and then immediately re-open the same PCM as part of their
initialization; for example applications built with the It can also be useful when playing short audio files in quick succession. It will reduce the gap between playbacks caused by Bluetooth audio transport acquisition. | |
| --io-rt-priority=NUM | |
Set the FIFO scheduler real-time priority of the I/O threads to NUM. By default all I/O threads run at the same priority as the main thread. This option allows the user to increase the priority of the I/O threads. This can be useful when playing audio with a low latency requirement. It is recommended to use this option when using the HFP profile with the mSBC codec, as the Linux kernel does not provide any buffering for the mSBC SCO socket. If the data are not read from the socket in time, the kernel will drop them. This can lead to lots of "Missing mSBC packets" warnings which will be audible as clicks in the audio. For more information about scheduling policies and priorities see
| |
| --disable-realtek-usb-fix | |
| Since Linux kernel 5.14 Realtek USB adapters have required bluealsad to apply a fix for mSBC. This option disables that fix and may be necessary when using an earlier kernel. | |
| --a2dp-force-mono | |
| Force monophonic sound for A2DP profile. | |
| --a2dp-force-audio-cd | |
| Force 44.1 kHz sample rate for A2DP profile. Some Bluetooth devices can handle streams sampled at either 48 kHz or 44.1kHz, in which case they normally default to using 48 kHz. With this option, bluealsad will request such a device uses only 44.1 kHz sample rate. | |
| --sbc-quality=MODE | |
Set SBC encoder quality. Default value is high. The MODE can be one of:
| |
| --mp3-algorithm=TYPE | |
Select LAME encoder internal algorithm. Default value is expensive. The TYPE can be one of:
If CPU power consumption is not an issue, one might safely select best as the algorithm type. Also, please note that the true quality is determined by the selected bit rate or used VBR quality option (--mp3-vbr-quality). | |
| --mp3-vbr-quality=MODE | |
Set variable bit rate (VBR) quality. Default value is standard. The MODE can be one of:
| |
| --aac-afterburner | |
| Enables Fraunhofer AAC afterburner feature, which is a type of analysis by synthesis algorithm. This feature increases the audio quality at the cost of increased processing power and overall memory consumption. | |
| --aac-bitrate=BPS | |
| Set the target bit rate for constant bit rate (CBR) mode or the maximum peak bit rate for variable bit rate (VBR) mode. Default value is 220000 bits per second. | |
| --aac-latm-version=NUM | |
Select LATM syntax version used for AAC audio transport. Default value is 1. The NUM can be one of:
| |
| --aac-true-bps | Enable true "bit per second" bit rate. A2DP AAC specification requires that for the constant bit rate (CBR) mode every RTP frame has the same bit rate and for the variable bit rate (VBR) mode the maximum peak bit rate limit is also per RTP frame. However, a single RTP frame does not contain a single full second of audio. This option enables true bit rate calculation (per second), which means that per RTP frame bit rate may vary even for CBR mode. This feature is not enabled by default, because it violates A2DP AAC specification. Enabling it should result in an enhanced audio quality, but will for sure produce fragmented RTP frames. If RTP fragmentation is not supported by used A2DP sink device (e.g., headphones) one might hear clearly audible clicks in the playback audio. In such case, please do not enable this option. |
| --aac-vbr | Prefer variable bit rate mode over constant bit rate mode. Please note, that this option does not necessarily mean that the variable bit rate (VBR) mode will be used. Used AAC configuration depends on a remote Bluetooth device capabilities. |
| --lc3plus-bitrate=BPS | |
| Set LC3plus encoder bit rate for constant bit rate mode (CBR) as BPS. Default value is 396800 bits per second. | |
| --ldac-abr | Enables LDAC adaptive bit rate, which will dynamically adjust encoder quality based on the connection stability. |
| --ldac-quality=MODE | |
Specifies LDAC encoder quality. Default value is standard. The MODE can be one of:
| |
| --midi-advertisement | |
| Advertise BLE-MIDI service using Bluetooth LE advertising. | |
| --xapl-resp-name=NAME | |
| Set the product name send in the XAPL response message. By default, the name is set as "BlueALSA". However, some devices (reported with e.g., Sony WM-1000XM4) will not provide battery level notification unless the product name is set as "iPhone". | |
bluealsad provides support for Bluetooth Advanced Audio Distribution Profile (A2DP), Hands-Free Profile (HFP), Headset Profile (HSP) and Bluetooth Low Energy MIDI (BLE-MIDI). A2DP profile is dedicated for streaming music (i.e., stereo, 48 kHz or higher sample rates), while HFP and HSP for two-way voice transmission (mono, 8 kHz or 16 kHz sample rate). BLE-MIDI, on the other hand, is used for transmitting MIDI messages over Bluetooth LE.
The Bluetooth audio profiles are not peer-to-peer; they each have a source or gateway role (a2dp-source, hfp-ag, or hsp-ag) and a sink or target role (a2dp-sink, hfp-hf, hsp-hs). The source/gateway role is the audio player (e.g., mobile phone), the sink/target role is the audio renderer (e.g., headphones or speaker). The bluealsad daemon can perform any combination of profiles and roles, although it is most common to use it either as a source/gateway:
bluealsad -p a2dp-source -p hfp-ag -p hsp-agor as a sink/target:
bluealsad -p a2dp-sink -p hfp-hf -p hsp-hsor with oFono for HFP support,
source/gateway:
bluealsad -p a2dp-source -p hfp-ofono -p hsp-agsink/target:
bluealsad -p a2dp-sink -p hfp-ofono -p hsp-hsWith A2DP, bluealsad always includes the mandatory SBC codec and may also include various optional codecs like AAC, aptX, and other.
With HFP, bluealsad always includes the mandatory CVSD codec and may also include the optional mSBC and LC3-SWB codecs.
The full list of available optional codecs, which depends on selected compilation options, will be shown with bluealsad command-line help message.
The list of profile NAME-s accepted by the --profile=NAME option:
- a2dp-source - Advanced Audio Source (streaming audio to connected device)
- a2dp-sink - Advanced Audio Sink (receiving audio from connected device)
- hfp-ofono - Hands-Free AG/HF handled by oFono
- hfp-ag - Hands-Free Audio Gateway
- hfp-hf - Hands-Free
- hsp-ag Headset Audio Gateway
- hsp-hs - Headset
- midi - Bluetooth LE MIDI
The hfp-ofono and midi profiles are available only when bluealsad was compiled respectively with oFono and BLE-MIDI support.
Enabling HFP over oFono will automatically disable hfp-hf and hfp-ag. Also, it is important to note that BlueZ permits only one service to register the HFP profile, and that service is automatically registered with every HCI device.
For the A2DP profile, BlueZ allows each HCI device to be registered to a
different service, so it is possible to have multiple instances of
bluealsad offering A2DP support, each with a unique service name given with
the --dbus= option, so long as they are registered to different HCI devices
using the --device= option. See the EXAMPLES below.
A profile connection does not immediately initiate the audio stream(s); audio can only flow when the profile transport is "acquired". Acquisition can only be performed by the source/gateway role. When acting as source/gateway, bluealsad acquires the profile transport (i.e., initiates the audio connection) when a client opens a PCM. When bluealsad is acting as target, a client can open a PCM as soon as the profile is connected, but the audio stream(s) will not begin until the remote source/gateway has acquired the transport.
The Bluetooth specifications for HFP and HSP include optional support for volume control of the target by the gateway device. For A2DP, volume control is optionally provided by the AVRCP profile. bluealsad provides a single, consistent, abstracted interface for volume control of PCMs. This interface can use the native Bluetooth features or alternatively bluealsad also implements its own internal volume control, called "soft-volume". The default behavior is to use native Bluetooth volume control.
When using soft-volume, bluealsad scales PCM samples before encoding, and after decoding, and does not interact with the Bluetooth AVRCP volume property or HFP/HSP volume control. Volume can only be modified by local clients. (Note that Bluetooth headphones or speakers with their own volume controls will still be able to alter their own volume, but this change will not be notified to bluealsad local clients, they will only see the soft-volume setting).
When using native volume control, bluealsad links the PCM volume setting to the AVRCP volume property or HFP/HSP volume control. No scaling of PCM samples is applied. Volume can be modified by both local clients and the remote device. Local clients will be notified of volume changes made by controls on the remote device.
A2DP native volume control does not permit independent volume values for audio channels. Because of this, when a client sets different values for each audio channel, bluealsad will set the Bluetooth volume as the average of all audio channels.
Volume level, mute status, and soft-volume selection can all be controlled for each PCM by using the D-Bus API (or by using ALSA plugins, see bluealsa-plugins(7) for more information). The current value of these settings for each PCM is stored in the filesystem so that the device can be disconnected and later re-connected without losing its volume settings.
When a device is connected, the volume level of its PCMs is set according to the following criteria (highest priority first):
- saved value from previous connection of the device
- value set by the
--initial-volumecommand line option- 100%
its mute status according to:
- saved value from previous connection
- false
and its soft-volume status according to:
- saved value from previous connection
- false (i.e., use native volume control)
When native volume control is enabled, then the remote device may also modify the volume level after this initial setting. Mute and soft-volume are implemented locally by the bluealsad daemon and cannot be modified by the remote device.
Note that bluealsad relies on support from BlueZ to implement native volume control for A2DP using AVRCP, and BlueZ has not always provided robust support here. It is recommended to use BlueZ release 5.65 or later to be certain that native A2DP volume control will always be available with those devices which provide it.
BlueALSA service D-Bus policy file. D-Bus will deny all access to the org.bluealsa service (even to root) unless permission is granted by a policy file. The default file permits only root to own this service, and only members of the audio group to exchange messages with it. BlueALSA installs its default file into the directory /usr/share/dbus-1/system.d, but the distribution or local administrator may override that by placing a modified policy file into /etc/dbus-1/system.d
- /var/lib/bluealsa/XX:XX:XX:XX:XX:XX
- BlueALSA volume persistent state storage. Files are named after the Bluetooth device address to which they refer.
Emulate Bluetooth headset with A2DP and HSP support:
bluealsad -p a2dp-sink -p hsp-hsOn systems with more than one HCI device, it is possible to expose different profiles on different HCI devices. A system with three HCI devices might (for example) use hci0 for an A2DP sink service named "org.bluealsa.sink" and both hci1 and hci2 for an A2DP source service named "org.bluealsa.source". Such a setup might be created as follows:
bluealsad -B sink -i hci0 -p a2dp-sink &
bluealsad -B source -i hci1 -i hci2 -p a2dp-source &Setup like this will also require a change to the BlueALSA D-Bus configuration file in order to allow connection with BlueALSA services with suffixed names. Please add following lines to the BlueALSA D-Bus policy:
...
<allow send_destination="org.bluealsa.sink" />
<allow send_destination="org.bluealsa.source" />
...Copyright (c) 2016-2024 Arkadiusz Bokowy.
The bluez-alsa project is licensed under the terms of the MIT license.
bluealsactl(1), bluealsa-aplay(1), bluealsa-rfcomm(1),
bluetoothctl(1), bluealsa-plugins(7), bluetoothd(8)
- Project web site
- https://github.com/arkq/bluez-alsa