Stuck on Starting kernel ... S905x generic

[mangunan]

Booting from usb flashdisk, stuck on Starting Kernel ...
Device is HG680P, amlogic S905x, 2GB
Here log from TTL

U-Boot 2015.01 (Aug 15 2018 - 12:27:30)

DRAM:  2 GiB
Relocation Offset is: 76ec9000
gpio: pin GPIOAO_6 (gpio 106) value is 0
gpio: pin GPIOH_8 (gpio 57) value is 1
gpio: pin GPIOH_9 (gpio 58) value is 0
gpio: pin GPIOAO_9 (gpio 109) value is 0
gpio: pin GPIOAO_5 (gpio 105) value is 1
register usb cfg[0][1] = 0000000077f5f9d8
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000073ec9dd0
aml_priv->desc_buf = 0x0000000073ecc0f0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
      Amlogic multi-dtb tool
      Multi dtb detected
gpio: pin GPIOAO_6 (gpio 106) value is 0
gpio: pin GPIOH_8 (gpio 57) value is 1
gpio: pin GPIOH_9 (gpio 58) value is 0
gpio: pin GPIOAO_9 (gpio 109) value is 0
gpio: pin GPIOAO_5 (gpio 105) value is 1
GPIOAO_4 value board_id_gpio = 0
saradc: check dts: FDT_ERR_BADMAGIC, load default parameters
-----board_version[9]
      unified board, board id adc = 9
Fiberhome GPIOAO_4 power on!!!!!      Multi dtb tool version: v2 .
      Support 4 dtbs.
        aml_dt soc: gxl platform: p212 variant: 2gs
        dtb 0 soc: gxl   plat: p212   vari: 1g
        dtb 1 soc: gxl   plat: p212   vari: 1gs
        dtb 2 soc: gxl   plat: p212   vari: 2g
        dtb 3 soc: gxl   plat: p212   vari: 2gs
      Find match dtb: 3
start dts,buffer=0000000073ece970,dt_addr=0000000073eeb970
parts: 12
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06: instaboot   0000000020000000 1
07:      boot   0000000002000000 1
08:    system   0000000040000000 1
09:     cache   0000000020000000 2
10:    params   0000000000800000 4
11:      data   ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is :
        name                        offset              size              flag
===================================================================================
   0: bootloader                         0            400000                  0
   1: reserved                     2400000           4000000                  0
   2: cache                        6c00000          20000000                  2
   3: env                         27400000            800000                  0
   4: logo                        28400000           2000000                  1
   5: recovery                    2ac00000           2000000                  1
   6: rsv                         2d400000            800000                  1
   7: tee                         2e400000            800000                  1
   8: crypt                       2f400000           2000000                  1
   9: misc                        31c00000           2000000                  1
  10: instaboot                   34400000          20000000                  1
  11: boot                        54c00000           2000000                  1
  12: system                      57400000          40000000                  1
  13: params                      97c00000            800000                  4
  14: data                        98c00000         139400000                  4
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
board_late_init,defenv!
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 4  vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
rx version is 2.0  div=10
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
      Amlogic multi-dtb tool
      Multi dtb detected
gpio: pin GPIOAO_6 (gpio 106) value is 0
gpio: pin GPIOH_8 (gpio 57) value is 1
gpio: pin GPIOH_9 (gpio 58) value is 0
gpio: pin GPIOAO_9 (gpio 109) value is 0
gpio: pin GPIOAO_5 (gpio 105) value is 1
GPIOAO_4 value board_id_gpio = 0
saradc: check dts: FDT_ERR_BADMAGIC, load default parameters
-----board_version[9]
      unified board, board id adc = 9
Fiberhome GPIOAO_4 power on!!!!!      Multi dtb tool version: v2 .
      Support 4 dtbs.
        aml_dt soc: gxl platform: p212 variant: 2gs
        dtb 0 soc: gxl   plat: p212   vari: 1g
        dtb 1 soc: gxl   plat: p212   vari: 1gs
        dtb 2 soc: gxl   plat: p212   vari: 2g
        dtb 3 soc: gxl   plat: p212   vari: 2gs
      Find match dtb: 3
Net:   dwmac.c9410000
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]failed to get fb addr for logo
[OSD]use default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]load fb addr from dts
[OSD]failed to get fb addr for logo
[OSD]use default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=3840, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
InUsbBurn
noSof
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
card out
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
emmc/sd response timeout, cmd1, status=0x1ff2800
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
reading s905_autoscript
1273 bytes read in 28 ms (43.9 KiB/s)
## Executing script at 01020000
reading bootscript
3831 bytes read in 27 ms (137.7 KiB/s)
## Executing script at 01080000
reading boot.config
1165 bytes read in 22 ms (50.8 KiB/s)
Trying config box-config/kernel-6.x.y.config...
reading box-config/kernel-6.x.y.config
778 bytes read in 50 ms (14.6 KiB/s)
Trying config box-config/kernel-6.x.y-mainline-.config...
reading box-config/kernel-6.x.y-mainline-.config
** Unable to read file box-config/kernel-6.x.y-mainline-.config **
Trying config box-config/kernel-6.6.y.config...
reading box-config/kernel-6.6.y.config
** Unable to read file box-config/kernel-6.6.y.config **
Trying config box-config/kernel-6.6.29-meson64.config...
reading box-config/kernel-6.6.29-meson64.config
** Unable to read file box-config/kernel-6.6.29-meson64.config **
Trying config box-config/box-s905x_generic.config...
reading box-config/box-s905x_generic.config
407 bytes read in 30 ms (12.7 KiB/s)
Trying config box-config/gx-default-mainline.config...
reading box-config/gx-default-mainline.config
866 bytes read in 51 ms (15.6 KiB/s)
Trying config box-config/gx-debug-mainline-.config...
reading box-config/gx-debug-mainline-.config
** Unable to read file box-config/gx-debug-mainline-.config **
Trying config boot.config...
reading boot.config
1165 bytes read in 22 ms (50.8 KiB/s)
reading dtb-6.6.29-meson64/amlogic/meson-gxl-p212-generic.dtb
28569 bytes read in 68 ms (410.2 KiB/s)
Using devicetree [dtb-6.6.29-meson64/amlogic/meson-gxl-p212-generic.dtb]
reading vmlinuz-6.6.29-meson64
22628360 bytes read in 11937 ms (1.8 MiB/s)
Starting linux with cmdline: root=/dev/sda2 rootfstype=ext4 rootwait rw console=tty0 no_console_suspend consoleblank=0 coherent_pool=2M net.ifnames=0 fsck.repair=yes fsck.mode=skip init_on_                                                alloc=1 init_on_free=1 randomize_kstack_offset=on kfence.sample_interval=100 debugfs=off kfence.deferrable=1 watchdog.stop_on_reboot=0

aml log : Sig Check 1208
** Bad device usb 1 **
** Bad device usb 2 **
** Bad device usb 3 **
** Unrecognized filesystem type **
[imgread]szTimeStamp[2018081512514071]
[imgread]secureKernelImgSz=0x8a1800
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =73ef63d0
copy done
      Amlogic multi-dtb tool
      Single dtb detected
load dtb from 0x4000000 ......
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x01080000, end = 0x0211cdc0
   reserving fdt memory region: addr=4000000 size=7000
   Loading Ramdisk to 73d58000, end 73eb6800 ... OK
   Loading Device Tree to 0000000073d4e000, end 0000000073d57fff ... OK
signature:
fdt_instaboot: no instaboot image

Starting kernel ...

uboot time: 19227394 us

Thanks