setup_macros.cfg

## Warning, some of the helper macros in start print have been masked with a leading "_"

[gcode_macro SETUP_BED]
gcode:
    {% set TOL_CORNERS = params.TOL_CORNERS|default(10)|float %}
    {% set my_tg = params.TOL_GANTRY|default(0.025)|float %}
    status_homing
    G28
    {% if printer.z_tilt %}
        M117 Tilting Gantry {my_tg}
        UPDATE_DELAYED_GCODE ID=clear_display DURATION=10
        Z_TILT_ADJUST RETRY_TOLERANCE={my_tg}
    {% endif %}

    {% if printer.screws_tilt_adjust %}
        M117 Checking corners {TOL_CORNERS}
        UPDATE_DELAYED_GCODE ID=clear_display DURATION=10
        SCREWS_TILT_CALCULATE MAX_DEVIATION={TOL_CORNERS}
    {% endif %}
    
    PARK
[gcode_macro INTRO_LINE]
gcode:
          { action_respond_info("INTRO_LINE is depricated, call _INTRO_LINE from START_PRINT")}



# Requires a 200mm bed
[gcode_macro _INTRO_LINE]
gcode:
        M117 Intro Line
        UPDATE_DELAYED_GCODE ID=clear_display DURATION=10
        {% set travel_speed = printer.toolhead.max_velocity * 0.7 * 60 %}
        {% set z_travel_speed = printer.configfile.settings.printer.max_z_velocity * 60 %}

        G1 Y1 X0 F{travel_speed} ; go to edge of print
        G1 Z0.3 F{z_travel_speed} ;drop to height
        G92 E0.0
        M82 ;Absolute
        G1 Y100.0 E22.5 F1000.0 ; intro line
        G1 Y200.0 E37.5 F1000.0 ; intro line
        G1 Z1 F{z_travel_speed} ;lift, NO RETRACT
        G1 X1
        G1 F {travel_speed}
        G92 E0.0

[gcode_macro PRINT_START]
description: wrapper for START_PRINT
gcode:
    START_PRINT {rawparams}

[gcode_macro START_PRINT]
variable_version: 0.4
description: Does everythin to go from a cold printer to a successful print except a purge line.
gcode:
    _SOUND_YES
    {% set svv = printer.save_variables.variables %}
    {% set BED_TEMP = params.BED_TEMP|default(svv.setup_default_bed_temp)|float %}
    {% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(svv.setup_default_nozzle_temp)|float %}
    
    ## Check for alternate params
    {% if "BED" in params %}
        {% set BED_TEMP = params.BED|float %}
        { action_respond_info("Using alternate param BED=" + params.BED|string)}
    {% endif %}
    {% if "EXTRUDER" in params %}
        {% set EXTRUDER_TEMP = params.EXTRUDER|float %}
        { action_respond_info("Using alternate param EXTRUDER=" + params.EXTRUDER|string)}
    {% endif %}
     {% if "HOTEND" in params %}
        {% set EXTRUDER_TEMP = params.HOTEND|float %}
        { action_respond_info("Using alternate param HOTEND=" + params.HOTEND|string)}
    {% endif %}
    
    

    {% if svv.setup_version|float < version|float %}
        { action_raise_error("Setup data is older than macro version. You should check the values in INIT_SETUP and run it to update") }
    {% endif %}
    {% if svv.setup_use_bed_offset == 1  %}
        BED_DETAILS # tell us about the bed
    #{else}
    {% endif %}
    SET_ENCLOSURE preheat=1
    
    G92 E0 ; reset extruder
    G90 ; absolute
    M82 ; extruder absolute
    G92 E0 ; reset extruder
    

    M107 S0; turn off fan
    status_heating
    M117 Heating Bed to {BED_TEMP}
    UPDATE_DELAYED_GCODE ID=clear_display DURATION=10
    #M104 S120 ; set extruder warmup temp
    M140 S{BED_TEMP} ; start heating
    SETUP_BED TOL_CORNERS=0.2 TOL_GANTRY=0.02
    status_heating
    M190 S{BED_TEMP} ; wait for bed temp
    PARK
    M109 S{svv.setup_idle_temp}
    M117 Preheat Extruder
    UPDATE_DELAYED_GCODE ID=clear_display DURATION=10
    #SETUP_BED TOL_CORNERS=0.2 TOL_GANTRY=0.02
    status_leveling
    _LOAD_MESH_TEMP BED_TEMP={BED_TEMP}
    status_heating
    M104 S{EXTRUDER_TEMP}
    PARK
    #Set our baseline offset for nozzle height, this is based PROBE_CALIBRATE result
    
    #And apply changes for a different bed
    _BED_START_PRINT_OFFSETS
    M117 Heating Extruder to {EXTRUDER_TEMP}
    UPDATE_DELAYED_GCODE ID=clear_display DURATION=10
    M109 S{EXTRUDER_TEMP} ; wait for extruder temp
    M117 Starting Print
    UPDATE_DELAYED_GCODE ID=clear_display DURATION=10
    status_homing
    _SOUND_YES
    G28 #Try homing at end to fix gcode
    SET_ENCLOSURE on=1
    status_printing
    SET_SKEW CLEAR=1
    _INTRO_LINE
    #SKEW_PROFILE LOAD=default
    
[gcode_macro PRINT_END]
description: wrapper for END_PRINT
gcode:
    END_PRINT {rawparams}

[gcode_macro END_PRINT]
description: Clean up after a print, save mesh if SAVE_AT_END was used.
gcode:
    {% set svv = printer.save_variables.variables %}
    G91
    G1 E-6 F300 ;big retract/wipe
    G1 X-2 Y-2 F3000 ;big retract/wipe
    G90
    SET_SKEW CLEAR=1
    PRESENT

    M140 S0 ; turn off heatbed
    M104 S0 ; turn off hotend
    M107 S0; turn off fan
    SET_ENCLOSURE cooldown=1
       
    
    M84 X Y E     ; disable motors
    # BED_MESH_CLEAR ;We want this
    #SET_GCODE_OFFSET Z=0 ; We might want this
    # SET_PRESSURE_ADVANCE ADVANCE=0 ; same here
    
    ## What Should remain here is any adjustment we made to Z-Offset
    ## this way we can apply our live Z change to the probe offset without 
    ## bed offsets and setups offsets getting in the way
    ## We might be able to remove setup_nozzle_offset
    _BED_END_PRINT_OFFSETS
    M117 Print Done
    #FORCE_MESH_LOAD #removed becasue not needed
    _SAVE_IF_SET

[gcode_macro CANCEL_PRINT]
rename_existing: BASE_CANCEL_PRINT
gcode:
    TURN_OFF_HEATERS
    CLEAR_PAUSE
    SDCARD_RESET_FILE
    M107 S0 ; turn off fans
    SET_SKEW CLEAR=1
    PRESENT
    #ENCLOSURE_PURGE
    BASE_CANCEL_PRINT
    status_off
    SET_ENCLOSURE cooldown=1



[gcode_macro MY_PROBE_CALIBRATE]
description: Homes, removes bed mesh, does probe_calibrate in a defined position, remember to PARK affter ACCEPT and before SAVE_CONFIG
gcode:
    SET_GCODE_OFFSET Z=0
    G28
    {% if printer.z_tilt %}
        Z_TILT_ADJUST
    {% endif %}

    {% if printer["gcode_macro PROBE_OUT"] %}
        PROBE_OUT
    {% endif %}
    G1 Z30
    G1 X110 Y93
    PROBE_CALIBRATE