Q: How do I configure a port as an access port?
A. Add
tag=VLAN
to yourovs-vsctl add-port
command. For example, the following commands configure br0 with eth0 as a trunk port (the default) and tap0 as an access port for VLAN 9:$ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 tap0 tag=9If you want to configure an already added port as an access port, use
ovs-vsctl set
, e.g.:$ ovs-vsctl set port tap0 tag=9
Q: How do I configure a port as a SPAN port, that is, enable mirroring of all traffic to that port?
A. The following commands configure br0 with eth0 and tap0 as trunk ports. All traffic coming in or going out on eth0 or tap0 is also mirrored to tap1; any traffic arriving on tap1 is dropped:
$ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 tap0 $ ovs-vsctl add-port br0 tap1 \ -- --id=@p get port tap1 \ -- --id=@m create mirror name=m0 select-all=true output-port=@p \ -- set bridge br0 mirrors=@mTo later disable mirroring, run:
$ ovs-vsctl clear bridge br0 mirrors
Q: Does Open vSwitch support configuring a port in promiscuous mode?
A: Yes. How you configure it depends on what you mean by "promiscuous mode":
Conventionally, "promiscuous mode" is a feature of a network interface card. Ordinarily, a NIC passes to the CPU only the packets actually destined to its host machine. It discards the rest to avoid wasting memory and CPU cycles. When promiscuous mode is enabled, however, it passes every packet to the CPU. On an old-style shared-media or hub-based network, this allows the host to spy on all packets on the network. But in the switched networks that are almost everywhere these days, promiscuous mode doesn't have much effect, because few packets not destined to a host are delivered to the host's NIC.
This form of promiscuous mode is configured in the guest OS of the VMs on your bridge, e.g. with "ip link set <device> promisc".
The VMware vSwitch uses a different definition of "promiscuous mode". When you configure promiscuous mode on a VMware vNIC, the vSwitch sends a copy of every packet received by the vSwitch to that vNIC. That has a much bigger effect than just enabling promiscuous mode in a guest OS. Rather than getting a few stray packets for which the switch does not yet know the correct destination, the vNIC gets every packet. The effect is similar to replacing the vSwitch by a virtual hub.
This "promiscuous mode" is what switches normally call "port mirroring" or "SPAN". For information on how to configure SPAN, see "How do I configure a port as a SPAN port, that is, enable mirroring of all traffic to that port?"
Q: How do I configure a DPDK port as an access port?
A: Firstly, you must have a DPDK-enabled version of Open vSwitch.
If your version is DPDK-enabled it may support the dpdk_version and dpdk_initialized keys in the configuration database. Earlier versions of Open vSwitch only supported the other-config:dpdk-init key in the configuration in the database. All versions will display lines with "EAL:..." during startup when other_config:dpdk-init is set to 'true'.
Secondly, when adding a DPDK port, unlike a system port, the type for the interface and valid dpdk-devargs must be specified. For example:
$ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 myportname -- set Interface myportname \ type=dpdk options:dpdk-devargs=0000:06:00.0Refer to :doc:`/intro/install/dpdk` for more information on enabling and using DPDK with Open vSwitch.
Q: How do I configure a VLAN as an RSPAN VLAN, that is, enable mirroring of all traffic to that VLAN?
A: The following commands configure br0 with eth0 as a trunk port and tap0 as an access port for VLAN 10. All traffic coming in or going out on tap0, as well as traffic coming in or going out on eth0 in VLAN 10, is also mirrored to VLAN 15 on eth0. The original tag for VLAN 10, in cases where one is present, is dropped as part of mirroring:
$ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 tap0 tag=10 $ ovs-vsctl \ -- --id=@m create mirror name=m0 select-all=true select-vlan=10 \ output-vlan=15 \ -- set bridge br0 mirrors=@mTo later disable mirroring, run:
$ ovs-vsctl clear bridge br0 mirrorsMirroring to a VLAN can disrupt a network that contains unmanaged switches. See ovs-vswitchd.conf.db(5) for details. Mirroring to a GRE tunnel has fewer caveats than mirroring to a VLAN and should generally be preferred.
Q: Can I mirror more than one input VLAN to an RSPAN VLAN?
A: Yes, but mirroring to a VLAN strips the original VLAN tag in favor of the specified output-vlan. This loss of information may make the mirrored traffic too hard to interpret.
To mirror multiple VLANs, use the commands above, but specify a comma-separated list of VLANs as the value for select-vlan. To mirror every VLAN, use the commands above, but omit select-vlan and its value entirely.
When a packet arrives on a VLAN that is used as a mirror output VLAN, the mirror is disregarded. Instead, in standalone mode, OVS floods the packet across all the ports for which the mirror output VLAN is configured. (If an OpenFlow controller is in use, then it can override this behavior through the flow table.) If OVS is used as an intermediate switch, rather than an edge switch, this ensures that the RSPAN traffic is distributed through the network.
Mirroring to a VLAN can disrupt a network that contains unmanaged switches. See ovs-vswitchd.conf.db(5) for details. Mirroring to a GRE tunnel has fewer caveats than mirroring to a VLAN and should generally be preferred.
Q: How do I configure mirroring of all traffic to a GRE tunnel?
A: The following commands configure br0 with eth0 and tap0 as trunk ports. All traffic coming in or going out on eth0 or tap0 is also mirrored to gre0, a GRE tunnel to the remote host 192.168.1.10; any traffic arriving on gre0 is dropped:
$ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 tap0 $ ovs-vsctl add-port br0 gre0 \ -- set interface gre0 type=gre options:remote_ip=192.168.1.10 \ -- --id=@p get port gre0 \ -- --id=@m create mirror name=m0 select-all=true output-port=@p \ -- set bridge br0 mirrors=@mTo later disable mirroring and destroy the GRE tunnel:
$ ovs-vsctl clear bridge br0 mirrors $ ovs-vsctl del-port br0 gre0
Q: Does Open vSwitch support ERSPAN?
A: Yes. ERSPAN version I and version II over IPv4 GRE and IPv6 GRE tunnel are supported. See ovs-fields(7) for matching and setting ERSPAN fields.
$ ovs-vsctl add-br br0 $ #For ERSPAN type 2 (version I) $ ovs-vsctl add-port br0 at_erspan0 -- \ set int at_erspan0 type=erspan options:key=1 \ options:remote_ip=172.31.1.1 \ options:erspan_ver=1 options:erspan_idx=1 $ #For ERSPAN type 3 (version II) $ ovs-vsctl add-port br0 at_erspan0 -- \ set int at_erspan0 type=erspan options:key=1 \ options:remote_ip=172.31.1.1 \ options:erspan_ver=2 options:erspan_dir=1 \ options:erspan_hwid=4
Q: How do I connect two bridges?
A: First, why do you want to do this? Two connected bridges are not much different from a single bridge, so you might as well just have a single bridge with all your ports on it.
If you still want to connect two bridges, you can use a pair of patch ports. The following example creates bridges br0 and br1, adds eth0 and tap0 to br0, adds tap1 to br1, and then connects br0 and br1 with a pair of patch ports.
$ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 tap0 $ ovs-vsctl add-br br1 $ ovs-vsctl add-port br1 tap1 $ ovs-vsctl \ -- add-port br0 patch0 \ -- set interface patch0 type=patch options:peer=patch1 \ -- add-port br1 patch1 \ -- set interface patch1 type=patch options:peer=patch0Bridges connected with patch ports are much like a single bridge. For instance, if the example above also added eth1 to br1, and both eth0 and eth1 happened to be connected to the same next-hop switch, then you could loop your network just as you would if you added eth0 and eth1 to the same bridge (see the "Configuration Problems" section below for more information).
If you are using Open vSwitch 1.9 or an earlier version, then you need to be using the kernel module bundled with Open vSwitch rather than the one that is integrated into Linux 3.3 and later, because Open vSwitch 1.9 and earlier versions need kernel support for patch ports. This also means that in Open vSwitch 1.9 and earlier, patch ports will not work with the userspace datapath, only with the kernel module.
Q: How do I configure a bridge without an OpenFlow local port? (Local port in the sense of OFPP_LOCAL)
A: Open vSwitch does not support such a configuration. Bridges always have their local ports.