temperature wasn't updated

[enghady-ahmed]

temperature wasn't updated in graph although i receive it in command text

[luc-github]

version of esp3d and web ui?
what is the printer Firmware and version?
What is M105 output?

[enghady-ahmed]

Dear Sir

-version of esp3d and web ui?
ESP3d = ESP3D-2.1.1
WEB Ui = UI: 0.9.5 / FW: 2.1.1.b8
"i use index file in doc file "
-what is the printer Firmware and version?
M115
FIRMWARE_NAME: Sprinter Experimental
PROTOCOL_VERSION:1.0
MACHINE_TYPE:Mendel EXTRUDER_COUNT:1
00000000-0000-0000-0000-000000000000
ok
-What is M105 output?
M105
ok T:25 @:0

[luc-github]

webui version is 0.9.5???
should be 2.xxx based
latest is 2.1b76

update it

[luc-github]

and I do not know if ESP3D-webui will work well with sprinter FW, because I never tested it

[enghady-ahmed]

Dear sir
But how i update it all what i did is upload index file that i found in doc folder

[luc-github]

you are in ESP3D-webUI repository - so the latest index.html.gz is here :
https://github.com/luc-github/ESP3D-WEBUI/blob/2.1/index.html.gz
and https://github.com/luc-github/ESP3D-WEBUI/tree/2.1/languages
upload it to replace the one you use

[enghady-ahmed]

unfortunately , same issue
temperature graph didn't draw and in this version i think there is temperature filter by default in command filed so i return to old version to get temperature as below , but i think it wasn't printer problem as i receive Temp periodically

[enghady-ahmed]

when i set heating it start rising but didn't show in graph it just show in command box , also i discover another problem as i can't print file from SD although file listed in SD box but when i print no respond , i try to make it using G code by type M20 to list file then M21 to init SD then select file by M23 filename and then M24 to start but unfortunately no respond , i get tired from that old board ATmega 644 it seems i must upgrade to arduino Mega if you have suggestion please tell me knowing that i can print from pronterface normal using cable or SD

[luc-github]

reading at https://reprap.org/wiki/Sjfw
the GCODE for printing are not compatible and temperature output is also different, I do not see the target tenmperature in M105 output.
The FW seems very old (https://github.com/ScribbleJ/sjfw) and no more maintained (10 years) - adding this support to ESP3D means list all GCODE for control and reporting and adapt ESP3D accordingly - it won't be done in ESP3d 2.X for sure, sorry.
It could be done for sure but does it worth it ? And I do not have bandwidth for this, you better switch to at least a Mega/ramps to get latest firmware support (Marlin, Repetier, etc...)

[enghady-ahmed]

Thanks for your valuable reply it seems i must upgrade , but can you help me with Gcode sequences that can i use manual to start print Gfile from SD like
1-M21 to int SD
2- M20 to list file
3- M23 "File name" to open it
4-M24 to start printing

i try the above , but it didn't work i try to check pronterface py file to know the code but i get confused

[luc-github]

check the wiki link I gave you above it says:

SD card support works in the firmware, but is not compatible with the Gcodes that Pronterface and ReplicatorG emit for SDcard access. This firmware presently has two Gcodes for SD access:
M204 - fetch filename from SD
M205 - print last fetched filename
The SD code may only work properly for 8.3 filenames.

[enghady-ahmed]

Thanks for your reply, i understand now that the problem was my printer is not marlin base it works with sprinter ver1 firmware so i must do the upgrade. Really i want to thank you for your support ❤️