forked from Klipper3d/klipper
-
Notifications
You must be signed in to change notification settings - Fork 7
/
.config.btteddy
74 lines (72 loc) · 2.1 KB
/
.config.btteddy
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
CONFIG_LOW_LEVEL_OPTIONS=y
# CONFIG_MACH_AVR is not set
# CONFIG_MACH_ATSAM is not set
# CONFIG_MACH_ATSAMD is not set
# CONFIG_MACH_LPC176X is not set
# CONFIG_MACH_STM32 is not set
# CONFIG_MACH_HC32F460 is not set
CONFIG_MACH_RP2040=y
# CONFIG_MACH_PRU is not set
# CONFIG_MACH_AR100 is not set
# CONFIG_MACH_LINUX is not set
# CONFIG_MACH_SIMU is not set
CONFIG_BOARD_DIRECTORY="rp2040"
CONFIG_MCU="rp2040"
CONFIG_CLOCK_FREQ=12000000
CONFIG_USBSERIAL=y
CONFIG_FLASH_SIZE=0x200000
CONFIG_FLASH_BOOT_ADDRESS=0x10000100
CONFIG_RAM_START=0x20000000
CONFIG_RAM_SIZE=0x42000
CONFIG_STACK_SIZE=512
CONFIG_FLASH_APPLICATION_ADDRESS=0x10000100
CONFIG_RP2040_SELECT=y
CONFIG_RP2040_HAVE_STAGE2=y
CONFIG_RP2040_FLASH_START_0100=y
# CONFIG_RP2040_FLASH_START_4000 is not set
CONFIG_RP2040_FLASH_W25Q080=y
# CONFIG_RP2040_FLASH_GENERIC_03 is not set
CONFIG_RP2040_STAGE2_FILE="boot2_w25q080.S"
CONFIG_RP2040_STAGE2_CLKDIV=2
CONFIG_RP2040_USB=y
# CONFIG_RP2040_SERIAL_UART0_PINS_0_1 is not set
# CONFIG_RP2040_SERIAL_UART0_PINS_12_13 is not set
# CONFIG_RP2040_SERIAL_UART0_PINS_16_17 is not set
# CONFIG_RP2040_SERIAL_UART0_PINS_28_29 is not set
# CONFIG_RP2040_SERIAL_UART1_PINS_4_5 is not set
# CONFIG_RP2040_SERIAL_UART1_PINS_8_9 is not set
# CONFIG_RP2040_SERIAL_UART1_PINS_20_21 is not set
# CONFIG_RP2040_SERIAL_UART1_PINS_24_25 is not set
# CONFIG_RP2040_CANBUS is not set
# CONFIG_RP2040_USBCANBUS is not set
CONFIG_RP2040_CANBUS_GPIO_RX=4
CONFIG_RP2040_CANBUS_GPIO_TX=5
CONFIG_USB=y
CONFIG_USB_VENDOR_ID=0x1d50
CONFIG_USB_DEVICE_ID=0x614e
CONFIG_USB_SERIAL_NUMBER_CHIPID=y
CONFIG_USB_SERIAL_NUMBER="12345"
#
# USB ids
#
# end of USB ids
CONFIG_WANT_GPIO_BITBANGING=y
CONFIG_WANT_DISPLAYS=y
CONFIG_WANT_SENSORS=y
CONFIG_WANT_LIS2DW=y
CONFIG_WANT_LDC1612=y
CONFIG_WANT_SOFTWARE_I2C=y
CONFIG_WANT_SOFTWARE_SPI=y
CONFIG_NEED_SENSOR_BULK=y
CONFIG_CANBUS_FREQUENCY=1000000
CONFIG_INITIAL_PINS=""
CONFIG_HAVE_GPIO=y
CONFIG_HAVE_GPIO_ADC=y
CONFIG_HAVE_GPIO_SPI=y
CONFIG_HAVE_GPIO_I2C=y
CONFIG_HAVE_GPIO_HARD_PWM=y
CONFIG_HAVE_STRICT_TIMING=y
CONFIG_HAVE_CHIPID=y
CONFIG_HAVE_STEPPER_BOTH_EDGE=y
CONFIG_HAVE_BOOTLOADER_REQUEST=y
CONFIG_INLINE_STEPPER_HACK=y