-
Notifications
You must be signed in to change notification settings - Fork 5
/
config.h
123 lines (108 loc) · 3.99 KB
/
config.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
/*
Copyright 2012 Jun Wako <[email protected]>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef CONFIG_H
#define CONFIG_H
#define VENDOR_ID 0xFEED
#define PRODUCT_ID 0x9898
#define DEVICE_VER 0x0100
#define MANUFACTURER t.m.k.
#define PRODUCT PC98 keyboard converter
#define DESCRIPTION converts PC98 keyboard protocol into USB
/* matrix size */
#define MATRIX_ROWS 16
#define MATRIX_COLS 8
/* key combination for command */
#define IS_COMMAND() ( \
host_get_first_key() == KC_CANCEL \
)
/* PC98 Reset Port shared with TXD */
#define PC98_RST_DDR DDRD
#define PC98_RST_PORT PORTD
#define PC98_RST_BIT 3
/* PC98 Ready Port */
#define PC98_RDY_DDR DDRD
#define PC98_RDY_PORT PORTD
#define PC98_RDY_BIT 4
/* PC98 Retry Port */
#define PC98_RTY_DDR DDRD
#define PC98_RTY_PORT PORTD
#define PC98_RTY_BIT 5
/*
* PC98 Serial(USART) configuration
* asynchronous, positive logic, 19200baud, bit order: LSB first
* 1-start bit, 8-data bit, odd parity, 1-stop bit
*/
/*
* Software Serial
*/
#define SERIAL_SOFT_BAUD 19200
#define SERIAL_SOFT_PARITY_ODD
#define SERIAL_SOFT_BIT_ORDER_LSB
#define SERIAL_SOFT_LOGIC_POSITIVE
/* RXD Port */
#define SERIAL_SOFT_RXD_DDR DDRD
#define SERIAL_SOFT_RXD_PORT PORTD
#define SERIAL_SOFT_RXD_PIN PIND
#define SERIAL_SOFT_RXD_BIT 2
#define SERIAL_SOFT_RXD_READ() (SERIAL_SOFT_RXD_PIN&(1<<SERIAL_SOFT_RXD_BIT))
/* RXD Interupt */
#define SERIAL_SOFT_RXD_VECT INT2_vect
#define SERIAL_SOFT_RXD_INIT() do { \
/* pin configuration: input with pull-up */ \
SERIAL_SOFT_RXD_DDR &= ~(1<<SERIAL_SOFT_RXD_BIT); \
SERIAL_SOFT_RXD_PORT |= (1<<SERIAL_SOFT_RXD_BIT); \
/* enable interrupt: INT2(falling edge) */ \
EICRA |= ((1<<ISC21)|(0<<ISC20)); \
EIMSK |= (1<<INT2); \
sei(); \
} while (0)
#define SERIAL_SOFT_RXD_INT_ENTER()
#define SERIAL_SOFT_RXD_INT_EXIT() do { \
/* clear interrupt flag */ \
EIFR = (1<<INTF2); \
} while (0)
/* TXD Port */
#define SERIAL_SOFT_TXD_DDR DDRD
#define SERIAL_SOFT_TXD_PORT PORTD
#define SERIAL_SOFT_TXD_PIN PIND
#define SERIAL_SOFT_TXD_BIT 3
#define SERIAL_SOFT_TXD_HI() do { SERIAL_SOFT_TXD_PORT |= (1<<SERIAL_SOFT_TXD_BIT); } while (0)
#define SERIAL_SOFT_TXD_LO() do { SERIAL_SOFT_TXD_PORT &= ~(1<<SERIAL_SOFT_TXD_BIT); } while (0)
#define SERIAL_SOFT_TXD_INIT() do { \
/* pin configuration: output */ \
SERIAL_SOFT_TXD_DDR |= (1<<SERIAL_SOFT_TXD_BIT); \
/* idle */ \
SERIAL_SOFT_TXD_ON(); \
} while (0)
/*
* Hardware Serial(UART)
*/
#ifdef __AVR_ATmega32U4__
#define SERIAL_UART_BAUD 19200
#define SERIAL_UART_DATA UDR1
#define SERIAL_UART_UBRR ((F_CPU/(16UL*SERIAL_UART_BAUD))-1)
#define SERIAL_UART_RXD_VECT USART1_RX_vect
#define SERIAL_UART_TXD_READY (UCSR1A&(1<<UDRE1))
#define SERIAL_UART_INIT() do { \
UBRR1L = (uint8_t) SERIAL_UART_UBRR; /* baud rate */ \
UBRR1H = (uint8_t) (SERIAL_UART_UBRR>>8); /* baud rate */ \
UCSR1B |= (1<<RXCIE1) | (1<<RXEN1); /* RX interrupt, RX: enable */ \
UCSR1B |= (0<<TXCIE1) | (1<<TXEN1); /* TX interrupt, TX: enable */ \
UCSR1C |= (1<<UPM11) | (1<<UPM10); /* parity: none(00), even(01), odd(11) */ \
sei(); \
} while(0)
#else
#error "USART configuration is needed."
#endif
#endif