-
Notifications
You must be signed in to change notification settings - Fork 1
/
Copy pathconfig.cfg
120 lines (90 loc) · 2.98 KB
/
config.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
[main]
; station coordinates
QTHlat=51.23456
QTHlon=18.76543
; cycle length (sec)
CycleInterval=19
; ignore sondes detected by other stations outside this radius (km)
Range=400
; consider signal lost after this time (min) - values below 4 minutes are not recommended
SignalTimeout=6
; database file (uncomment for multi-SDR setup)
#Database=/tmp/freq_cycler.db
[landing_mode]
; landing mode distance (km)
Distance=70
; landing mode altitude (m)
Altitude=4000
[aprs_cycles]
; This makes sdrtst make extra cycles to listen for 70cm APRS.
; You have to use sondeudp -D option to reroute soundstream to software
; APRS decoder, like direwolf
; how long an APRS cycle will last (sec)
AprsCycle=73
; time between APRS cycles (sec)
; (this time is not guaranteed, it will wait for sonde cycle to end)
AprsInterval=90
; sdrtst configuration for APRS
AprsSdrtstConfig="f 432.500 0 0 0 90"
; updates to this file/dir will mean something was heard on APRS 70cm
#AprsLog=/var/log/direwolf
; if something was received in last 10 minutes, use following APRS cycle lengths:
ActiveAprsCycle=180
ActiveAprsInterval=27
; create this flagfile when in APRS cycle
AprsFlagFile=/tmp/freq_cycler_aprs_cycle.tmp
; set Raspberry GPIO pin (BCM numbering) high during APRS cycle
; (use negative value to set low)
#AprsGPIO=-22
[auto_channels]
; uncomment lines below to enable auto-adjusting of number of available
; channels according to Raspberry core temperature (see readme.txt)
#Sensor=/sys/class/thermal/thermal_zone0/temp
#LowTemp=50
#MaxChannels=15
#HighTemp=75
#MinChannels=2
[sonde_standard]
; parameters for RS-41, RS-92 and DFM sondes:
; blind-scanning range
ScanRangeLow=400000
ScanRangeHigh=406000
; bling-scanning step (kHz), use 0 to disable scanning
ScanStep=10
; known sondes frequencies, space-delimited
Known=402100 403000 401100 405100
; templates for sdrtst config line (see readme.txt if using original dxlAPRS!)
SdrtstTemplate="5 0 60 60 12000"
; AFC-range AFC-offset squelch% lowpass% IF-width
; landing mode: alternate parameters
#LdgSdrtstTemplate="5 0 0 60 12000"
[sonde_pilotsonde]
; parameters for Pilotsonde:
ScanRangeLow=400000
ScanRangeHigh=406000
ScanStep=0
Known=401465 401475 401485 401495 401505 401515 402465 402475 402485 402495 402505 402515
SdrtstTemplate1="10 1200 60 0 12000"
SdrtstTemplate2="10 2400 60 0 24000"
; AFC-range AFC-offset squelch% lowpass% IF-width
; landing mode: create extra channels around original QRG (low high step) [kHz]
; USE WITH CARE: this can easily overload the CPU
#LdgModeFreqSpread="-3 6 3"
[sonde_m10]
; parameters for M10/M20 sonde:
ScanRangeLow=400000
ScanRangeHigh=406000
ScanStep=10
Known=
SdrtstTemplate="5 -3500 60 95 24000"
; AFC-range AFC-offset squelch% lowpass% IF-width
#LdgSdrtstTemplate="1 -3500 0 95 24000"
#LdgModeFreqSpread="4 12 2"
[sonde_atms]
# parameters for ATMS sonde:
ScanRangeLow=400000
ScanRangeHigh=406000
ScanStep=0
Known=404300
SdrtstTemplate="10 0 0 0 96000"
; AFC-range AFC-offset squelch% lowpass% IF-width