PATHS.in.empty

# paths for the various Makefiles and run scripts
# on the current installation (either x86 or cray)
# v1.2

# --- SDAVI --------------------------------------------------------------------
# absolute paths are needed

# unselect if no need to build
export SDAVI_BUILD_FOR_NETCDF=YES
export SDAVI_BUILD_FOR_HDF5=YES

# for compilation
export SDAVI_NETCDF_PATH=__NETCDF_PATH__
export SDAVI_HDF5_1_8_PATH=
export SDAVI_HDF5_1_10_PATH=

# for benchmarking with LIBLSB (optional)
export SDAVI_LIBLSB_PATH=


# for networking: IP address detection
export SDAVI_IFCONFIG=/sbin/ifconfig
export SDAVI_INTERFACE=eth0
#e.g., eth0, ipogif0 (Piz Daint)

# function to get machine IP address (machine dependent)
# alternative for x86: provide hard coded IP address
#export SDAVI_IP=$($SDAVI_IFCONFIG $SDAVI_INTERFACE | grep "inet" | cut -d ':' -f 2 | cut -d ' ' -f 1)
export SDAVI_IP="127.0.0.1"
#export SDAVI_IP=$($SDAVI_IFCONFIG $SDAVI_INTERFACE | grep "inet " | cut -d ' ' -f 10)


# use path that matches the HDF5 version needed for Python h5py in client applications
# we need v1.10
export SDAVI_H5PY_HDF5_PATH=$SDAVI_HDF5_1_10_PATH
export SDAVI_CLIENT_LIBDVLH=libdvlh10.so

# if you need v1.8 for the client, then switch the comments
#export SDAVI_H5PY_HDF5_PATH=$SDAVI_HDF5_1_8_PATH
#export SDAVI_CLIENT_LIBDVLH=libdvlh8.so

# path to this main folder of sdavi, which will be accessed from various locations
export SDAVI_DIR=__SDAVI_DIR__

# deduced from SDAVI_DIR
export DV_LIB_DIR=$SDAVI_DIR/lib

# --- COSMO --------------------------------------------------------------------
# absolute paths are needed

export COSMO_DIR=__COSMO_DIR__
export COSMO_RUN_CMD=__COSMO_RUN_CMD__

# --- FLASH --------------------------------------------------------------------
# absolute paths are needed

# path to version 4.4 folder of FLASH (contains setup file)
# e.g. FLASH_DIR=~/FLASH/FLASH4.4 
export FLASH_DIR=~/FLASH/FLASH4.4

# path to HDF5 v1.8 base folder
# e.g. /usr/local/hdf5_1_8
# see above for SDAVI_HDF5_1_8_PATH
export FLASH_HDF5_PATH=$SDAVI_HDF5_1_8_PATH

# the following paths need to be set only for the problems to be tested
# folders will be generated as needed, paths should be on a scratch drive if available
# WARNING: If the folder exists, all files in it will be deleted!
export FLASH_RESTART_1_1=~/test_flash/restart_1_1
export FLASH_RESTART_1_8=~/test_flash/restart_1_8
export FLASH_RESTART_1_27=~/test_flash/restart_1_27
export FLASH_RESTART_16_512=~/test_flash/restart_16_512
export FLASH_RESTART_54_1728=~/test_flash/restart_54_1728

# here the actual experiment will create and access all result files
# folders will be generated as needed, path should be on a scratch drive if available
# WARNING: If the folder exists, all files in it will be deleted!
export FLASH_RUN_DIR=~/test_flash/run


# Running FLASH on Cray uses this additional variables,
# and additional configurations in the experiment .sbatch files,
# in run_sdavi.sh and in the template .sh files in the folder driver.
# Already for compilation/restart file generation, the .sbatch file in folder for_FLASH
# needs to be adjusted.
# All the modifications are too complex to do them here with small adjustments of
# variables. Please check these mentioned files in detail and adjust them to
# your system as needed.


# adjust the launch command for batches
# used in
# - the Makefile in ./for_FLASH
# additional adjustments may be needed in the .sbatch files for your system
export FLASH_SBATCH_CMD=sbatch

# Please note that running the larger allocations can get quite expensive rather quickly,
# in particular with experiments run later.