Part Number: X867281-005 Codename: Lithium
Components:
- Infrared Receiver (U1)
- Soundchip - ISD9160F (U4)
- Connector to sound speaker (J1)
- Wifi Antenna connector (J2)
- FPC connector (J3)
- Motherboard connector (J8)
- Unpopulated (SW2)
The RF Unit, compared to Xbox 360, is very simple. It does not contain any RF hardware onboard. It only contains an IR Receiver, the Nuvoton Soundcorder Chip (which also handles button presses from the front panel touch buttons) and an internal antenna. Actual RF communication is happening via a Wifi module.
Communication from the Nuvotun chip to the Southbridge is done via I2C.
Pinout
| Pin | Function |
|---|---|
| 1 | LED Nexus |
| 2 | LED Halo |
| 3 | LED Zone |
| 4 | 5V (VCC) |
| 5 | I2C CLK |
| 6 | I2C DATA |
| 7 | IR Data |
| 8 | PWR Switch (N) |
| 9 | GND |
| 10 | EJECT Switch (N) |
| 11 | INT_N |
| 12 | 3,3V STDBY |
| 13 | BIND Switch (N) |
| 14 | GND |
| 15 | - |
| 16 | - |
| 17 | - |
| 18 | GND |
| 19 | GND |
Pinout
| Pin | Function | ISD9160F Pin |
|---|---|---|
| 1 | Power | 9 |
| 2 | Power | 8 |
| 3 | - | - |
| 4 | - | - |
| 5 | - | - |
| 6 | Eject | 7 |
| 7 | Eject | 6 |
Bridge the respective pins briefly to trigger action.
FPC Cable / capacitive front panel buttons are directly wired to the ISD-Chip.
Responsible for playing the power-on/off and eject sounds.
Model: ISD9160F
Datasheet: ISD9160FI
Pinout (from the official datasheet linked above)
This IC has multiple possible pin-configurations, the following are verified signals.
| Pin | Function |
|---|---|
| 6 | Eject button (FPC - Pin 7) |
| 7 | Eject button (FPC - Pin 6) |
| 8 | Power button (FPC - Pin 2) |
| 9 | Power button (FPC - Pin 1) |
| 47 | I2C SCL (CLK) |
| 46 | I2C SDA (DAT) |
Captured via Logic Analyzer from Pin 5,6 on RF Unit.
I2C address: 0x5A
Commands
| Byte | Name | Args | Reads data |
|---|---|---|---|
| 0x48 | Register Write | Register, Data | No |
| 0xC0 | Interrupt Read | / | Yes |
| 0xC1 | Register Read | / | Yes |
| 0xC3 | Flash Read | Address U32-LE | Yes |
| 0x81 | Start Sound | Sound index | No |
| 0x02 | Stop Sound | / | No |
| 0x42 | Reset | 0x55 | No |
Registers
| Num | Name | Read/Write |
|---|---|---|
| 0x0C | Status | READ-ONLY |
| 0x04 | Address0 | R/W |
Available sounds
| Index | Name |
|---|---|
| 0x00 | PowerOn |
| 0x01 | Ding |
| 0x02 | PowerOff |
| 0x03 | DiscDrive1 |
| 0x04 | DiscDrive2 |
| 0x05 | DiscDrive3 |
| 0x06 | Plopp |
| 0x07 | No Disc |
| 0x08 | Plopp Louder |
Init sequence:
WRITE [CMD_REGISTER_WRITE, REG_STATUS, 0x01]
WRITE [CMD_REGISTER_WRITE, REG_ADDR0, 0xFF, 0xFF]
Play sound
WRITE [CMD_START, SOUND_INDEX]
Stop sound
WRITE [CMD_STOP]
Reset
WRITE [CMD_RESET, 0x55]
Write register
WRITE [CMD_REGISTER_WRITE, <REGISTER>, <DATA>]
Read register
WRITE [CMD_REGISTER_READ, <REGISTER>]
READ <DATA>
Read interrupt
WRITE [CMD_INTERRUPT_READ]
READ <DATA>
Flash read
WRITE [CMD_FLASH_READ, <Address as UINT32, little endian>]
READ <DATA> (8 bytes)
* Cut off first 2 bytes to yield 6 bytes of flash data
To get a sound playing, this is the full flow done by the console
- Init
- Stop
- Play sound
Codename: Sodium
Connector
| Pin | Function |
|---|---|
| 1 | LED Nexus |
| 2 | - |
| 3 | IR Blaster |
| 4 | PWR Switch (N) |
| 5 | EJECT Switch (N) |
| 6 | INT_N |
| 7 | 3,3V STDBY |
| 8 | 5V |
| 9 | ACC_RESET |
| 10 | IR (RX) |
| 11 | GND |
| 12 | USB2 (-) |
| 13 | USB2 (+) |
| 14 | GND |
| 15 | I2C CLK |
| 16 | I2C DATA |
Codename: Cactus
NOTE: Front panel on Xbox One X does not use I2C anymore.
| Pin | Function |
|---|---|
| 1 | IR (RX) |
| 2 | EJECT Switch (N) |
| 3 | - |
| 4 | IR Blaster |
| 5 | ACC_RESET |
| 6 | GND |
| 7 | USB2 (-) |
| 8 | USB2 (+) |
| 9 | 3,3V STDBY |
| 10 | GND |
| 11 | - |
| 12 | - |
| 13 | - |
| 14 | PWR Switch (N) |
| 15 | LED Nexus |
| 16 | 5V |
- DuRFUnitI2C - (Python) Communicate with the (PHAT) RF Unit and dump its flash
- Xbox One PHAT and One S Pictures from ifixit.com
- Xbox One X Pictures taken by jacksomness