Update help

Sources/NXVenom/switch/.packages/SC Wizard/Help/CPU/High Freq UV Level.txt

@@ -0,0 +1 @@
+High Freq UV Level: 1683-2601 MHz (UV7: 1581-2601 MHz)

Sources/NXVenom/switch/.packages/SC Wizard/Help/CPU/High Freq Vmin.txt

@@ -1,7 +1,3 @@
 Changing this value affects cpu voltage calculation
 
-CPU tune High Freq Vmin is used to fine tune voltage step in between lower and higher frequency bracket
-
-Between 1500-1900 you see flat voltage
-
-Tune High Freq Vmin is used by hardware to tune that
+Reduces voltages between 1683-2193 MHz

Sources/NXVenom/switch/.packages/SC Wizard/Help/CPU/Max Volt.txt → Sources/NXVenom/switch/.packages/SC Wizard/Help/CPU/Low Freq Vmin.txt

@@ -1 +1,3 @@
 Changing this value affects cpu voltage calculation
+
+Reduces voltages between 612-1122 MHz

Sources/NXVenom/switch/.packages/SC Wizard/Help/CPU/UV Level.txt

@@ -0,0 +1 @@
+Low Freq UV: 0-1581 MHz (UV7: 0-1428 MHz)

Sources/NXVenom/switch/.packages/SC Wizard/Help/CPU/Unlock.txt

@@ -0,0 +1,5 @@
+Ulock 2295-2601 freqs
+
+It gives small boost, but drains more power and rise temperature
+
+Recommended using only for Boost Clock & CPU heavy games

Sources/NXVenom/switch/.packages/SC Wizard/Help/CPU/Volt Limit.txt

@@ -0,0 +1 @@
+Max CPU volt is capped to 1160 mV, the switch will not boot at higher voltages

Sources/NXVenom/switch/.packages/SC Wizard/Help/GPU/GPU Scheduling.txt

@@ -0,0 +1 @@
+GPU scheduling off gives performance boost up to 3.3% but also power drain and higher temperatures

Sources/NXVenom/switch/.packages/SC Wizard/Help/GPU/UV Level.txt

@@ -0,0 +1,17 @@
+Reduce GPU power draw
+
+Mariko
+---
+
+0 : HiOPT table
+1 : Modified HiOPT (-20 mV on the last 3 freq)
+2 : High UV table
+3 : Custom static GPU Voltage Table (Use Gpu Configuator)
+
+Erista
+---
+
+0 : Default Table
+1 : Medel's GPU UV table with an offset of +30mV
+2 : Experimental dynamic high UV table
+3 : Custom static GPU Voltage Table (Use Gpu Configuator)

Sources/NXVenom/switch/.packages/SC Wizard/Help/GPU/Unlock.txt

@@ -0,0 +1,5 @@
+Ulock 1305 GPU freq
+
+It gives small boost, but drains more power and rise temperature
+
+Recommended using only for GPU heavy games

Sources/NXVenom/switch/.packages/SC Wizard/Help/GPU/Min Volt.txt → Sources/NXVenom/switch/.packages/SC Wizard/Help/GPU/Vmin.txt

@@ -2,4 +2,4 @@ High EMC Clocks will require gpu minimum voltage to be raised
 
 Default stock GPU vmin: 610mV
 
-SLT and HiOPT tabels uses 590mV as minimum voltage
+UV tabels uses 590mV as minimum voltage

Sources/NXVenom/switch/.packages/SC Wizard/Help/GPU/Max Volt.txt → Sources/NXVenom/switch/.packages/SC Wizard/Help/GPU/Volt Limit.txt

@@ -1,6 +1,6 @@
 Not recommended to increase value in order to protect from going over gpu pmic limits
 
-Recommended limit: 800mV@1228Mhz with HiOPT
+Recommended limit: 800mV@1228Mhz
 
 Any GPU Frequency that needs higher than vmax will be automatically removed and not available
 

Sources/NXVenom/switch/.packages/SC Wizard/Help/RAM/DRAM Timing.txt

@@ -1,5 +1,7 @@
 0: AUTO_ADJ: Auto adjust mtc table with LPDDR4 3733 Mbps specs, 16Gb density. Change timing with Advanced Config (Default)
 
-1: AUTO_ADJ_HP (Previously CUST_ADJ): Auto adjust only core timings
+1: AUTO_ADJ_LV: Less tight timings. It can help achieve higher frequencies or lower voltages
+
+1: AUTO_ADJ_LV_HP: LV mode with slightly tighter timings
 
 2: NO_ADJ: Use 1600 mtc table wihout adjusting (Timing becomes tighter if you raise dram clock)

Sources/NXVenom/switch/.packages/SC Wizard/Help/RAM/EMC Vddq.txt

@@ -3,6 +3,6 @@ Vddq is the supply voltage to the output buffers of a memory chip
 Proper voltage is essential for RAM stability
 
 Default: 600mV
-Official lpddr4(x) range: 570mV~650mV (600mV nominal)
+Official lpddr4(x) range: 570mV~700mV (600mV nominal)
 
 Higher values might improve stabilty on higher memory freqs

Sources/NXVenom/switch/.packages/SC Wizard/Help/RAM/HP Mode.txt

@@ -0,0 +1 @@
+Reduces timings latency but drains more power and rise temperature

Sources/NXVenom/switch/.packages/SC Wizard/Help/RAM/T1 tRCD.txt

@@ -0,0 +1,2 @@
+Scales with voltage
+Drop tRCD by 1 until unstable

Sources/NXVenom/switch/.packages/SC Wizard/Help/RAM/T2 tRP.txt

@@ -0,0 +1,2 @@
+Scales with voltage
+Drop tRP by 1 until unstable

Sources/NXVenom/switch/.packages/SC Wizard/Help/RAM/T3 tRAS.txt

@@ -0,0 +1 @@
+Reducing tRAS works well on Samsung RAM (MGCL, MGCJ)

Sources/NXVenom/switch/.packages/SC Wizard/Help/RAM/T8 tWLWL.txt

@@ -0,0 +1 @@
+tWLWL decreases timings related to write

Sources/NXVenom/switch/.packages/SC Wizard/Help/RAM/T9 tRDRD.txt

@@ -0,0 +1 @@
+tRDRD decreases timings related to read

Sources/NXVenom/switch/.packages/SC Wizard/Help/Timing Presets.txt

@@ -0,0 +1,29 @@
+Samsung AA-MGCL
+(14-14-26) 4-4-4-5-(4-4)
+
+Samsung AM-MGCJ
+(14-14-30) 3-3-2-5-(3-3)
+
+Samsung AB-MGCL
+(14-14-30) 3-3-3-5-(3-3)
+
+Samsung MGCH (Erista)
+(14-14-30) 1-3-2-5-(3-3)
+
+Micron WT:F
+(13-13-30) 5-4-3-5-(6-5)
+
+Micron WT:E
+(15-15-33) 4-3-2-5-(4-4)
+
+Micron WT:B
+(12-12-24) 5-2-3-5-(6-5)
+
+Hynix NEE
+(14-14-32) 2-5-3-5-(6-3)
+
+Hynix NME
+(15-15-36) 0-1-1-5-(1-1)
+
+Venom Default
+(15-15-33) 0-3-2-5-(2-2)

Sources/NXVenom/switch/.packages/Software Installer/Help/Fizeau.txt

@@ -0,0 +1,13 @@
+Adjust the color of your Nintendo Switch screen
+
+Features:
+
+- Modify the color temperature of the display
+
+- Filter colors to one single component
+
+- Apply color corrections: gamma, luminance, and color range
+
+- Schedule settings to be applied to dusk/dawn time, with smooth transitions
+
+- Configurable screen dimming

Sources/NXVenom/switch/.packages/Software Installer/Help/NX-Activity-Log.txt

@@ -0,0 +1,2 @@
+
+Homebrew application for the Nintendo Switch which displays play activity with more accuracy

Sources/NXVenom/switch/.packages/Software Installer/Help/TOTK UltraCam.txt

@@ -0,0 +1,3 @@
+UberHand package for Zelda TOTK UltraCam installation & management
+
+Support game versions 1.1.0, 1.1.1, 1.1.2, 1.2.0, 1.2.1