[Feature] Better chip unsafe pin definitions

include/Chipset.h

@@ -0,0 +1,234 @@
+#pragma once
+
+#include <driver/gpio.h>
+
+#include <bitset>
+
+// The following chipsets are supported by the OpenShock firmware.
+// To find documentation for a specific chipset, see the docs link.
+// You need to navigate to the datasheets pin's section, the unsafe pins are usually listed under the "Strapping Pins" section.
+// We want to avoid using these pins as they are used for boot mode and SDIO slave timing selection, and its easy to encounter issues if we use them.
+#pragma region Chipset Definitions
+// ESP8266EX
+//
+// Chips: ESP8266EX
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/0a-esp8266ex_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP8266EX
+#define OPENSHOCK_FW_CHIP_NAME "ESP8266EX"
+// GPIO3, GPIO1 is used for UART0 RXD/TXD.
+// GPIO0, GPIO2, and GPIO15 are used for boot mode and SDIO slave timing selection.
+#define CHIP_UNSAFE_GPIO(pin) (pin == GPIO_NUM_0 || pin == GPIO_NUM_1 || pin == GPIO_NUM_2 || pin == GPIO_NUM_3 || pin == GPIO_NUM_15)
+#endif
+
+// ESP8285
+//
+// Chips: ESP8285N08, ESP8285H16
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/0a-esp8285_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP8285
+#define OPENSHOCK_FW_CHIP_NAME "ESP8285"
+// GPIO3, GPIO1 is used for UART0 RXD/TXD.
+// GPIO0, GPIO2, and GPIO15 are used for boot mode and SDIO slave timing selection.
+#define CHIP_UNSAFE_GPIO(pin) (pin == GPIO_NUM_0 || pin == GPIO_NUM_1 || pin == GPIO_NUM_2 || pin == GPIO_NUM_3 || pin == GPIO_NUM_15)
+#endif
+
+// ESP8684
+//
+// Chips: ESP8684H1, ESP8684H2, ESP8684H4
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp8684_datasheet_en.pdf
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp8684_technical_reference_manual_en.pdf#bootctrl
+#ifdef OPENSHOCK_FW_CHIP_ESP8684
+#define OPENSHOCK_FW_CHIP_NAME "ESP8684"
+// GPIO3, GPIO1 is used for UART0 RXD/TXD.
+// GPIO8, GPIO9 are strapping pins used to control the boot mode adn ROM code printing
+#define CHIP_UNSAFE_GPIO(pin) (pin == GPIO_NUM_1 || pin == GPIO_NUM_3 || pin == GPIO_NUM_8 || pin == GPIO_NUM_9)
+#endif
+
+// ESP8685
+//
+// Chips: ESP8685H2, ESP8685H4
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp8685_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP8685
+#define OPENSHOCK_FW_CHIP_NAME "ESP8685"
+// GPIO20, GPIO21 is used for UART0 RXD/TXD.
+// GPIO2, GPIO8, GPIO9 are strapping pins.
+#define CHIP_UNSAFE_GPIO(pin) (pin == GPIO_NUM_2 || pin == GPIO_NUM_8 || pin == GPIO_NUM_9 || pin == GPIO_NUM_20 || pin == GPIO_NUM_21)
+#endif
+
+// ESP32
+//
+// Chips: ESP32-D0WD-V3, ESP32-D0WDR2-V3, ESP32-U4WDH, ESP32-S0WD, ESP32-D0WD, ESP32-D0WDQ6, ESP32-D0WDQ6-V3
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP32
+#define OPENSHOCK_FW_CHIP_NAME "ESP32"
+
+// GPIO1, GPIO3 is used for UART0 RXD/TXD.
+// GPIO0, GPIO2 is used to control the boot mode of the chip.
+// GPIO5, GPIO15 is used for SDIO slave timing selection.
+// GPIO6, GPIO7, GPIO8, GPIO9, GPIO11, GPIO16, GPIO17 is used for SPI flash connection. (DO NOT TOUCH)
+//
+// See: ESP32 Series Datasheet Version 4.3 Section 2.2 Pin Overview
+// See: ESP32 Series Datasheet Version 4.3 Section 2.4 Strapping Pins
+#define CHIP_UNSAFE_GPIO(pin)                                                                                                                                                                                                                                  \
+  (pin == GPIO_NUM_1 || pin == GPIO_NUM_3 || pin == GPIO_NUM_0 || pin == GPIO_NUM_2 || pin == GPIO_NUM_5 || pin == GPIO_NUM_15 || pin == GPIO_NUM_6 || pin == GPIO_NUM_7 || pin == GPIO_NUM_8 || pin == GPIO_NUM_9 || pin == GPIO_NUM_11 || pin == GPIO_NUM_16 \
+   || pin == GPIO_NUM_17)
+#endif
+
+// ESP32-PICO-D4
+//
+// Chips: ESP32-PICO-D4
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp32-pico_series_datasheet_en.pdf (Section 2.1.2 - 2.1.3 Pin Description and Pin Mapping between ESP and Flash/PSRAM)
+#ifdef OPENSHOCK_FW_CHIP_ESP32PICOD4
+#define OPENSHOCK_FW_CHIP_NAME "ESP32-PICO-D4"
+// GPIO3, GPIO1 is used for UART0 RXD/TXD.
+// GPIO25, GPIO27, GPIO29, GPIO30, GPIO31, GPIO32, GPIO33 is used for SPI flash connection. (DO NOT TOUCH)
+// GPIO12, GPIO0, GPIO2, GPIO15, and GPIO5 are used for boot mode and SDIO slave timing selection.
+#define CHIP_UNSAFE_GPIO(pin) (pin == GPIO_NUM_3 || pin == GPIO_NUM_1 || pin == GPIO_NUM_25 || pin == GPIO_NUM_27 || pin == GPIO_NUM_29 || pin == GPIO_NUM_30 || pin == GPIO_NUM_31 || pin == GPIO_NUM_32 || pin == GPIO_NUM_33 || pin == GPIO_NUM_12 || pin == GPIO_NUM_0 || pin == GPIO_NUM_2 || pin == GPIO_NUM_15 || pin == GPIO_NUM_5)
+#endif
+
+// ESP32-PICO-V3
+//
+// Chips:, ESP32-PICO-V3, ESP32-PICO-V3-02
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp32-pico_series_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP32PICOV3
+#define OPENSHOCK_FW_CHIP_NAME "ESP32-PICO-V3"
+// GPIO3, GPIO1 is used for UART0 RXD/TXD.
+// GPIO6, GPIO11, GPIO9, GPIO10 is used for SPI flash connection. (DO NOT TOUCH)
+// GPIO12, GPIO0, GPIO2, GPIO15, and GPIO5 are used for boot mode and SDIO slave timing selection.
+#define CHIP_UNSAFE_GPIO(pin) (pin == GPIO_NUM_3 || pin == GPIO_NUM_1 || pin == GPIO_NUM_6 || pin == GPIO_NUM_11 || pin == GPIO_NUM_9 || pin == GPIO_NUM_10 || pin == GPIO_NUM_12 || pin == GPIO_NUM_0 || pin == GPIO_NUM_2 || pin == GPIO_NUM_15 || pin == GPIO_NUM_5)
+#endif
+
+// ESP32-S2
+//
+// Chips: ESP32-S2, ESP32-S2FH2, ESP32-S2FH4, ESP32-S2FN4R2, ESP32-S2R2
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp32-s2_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP32S2
+#define OPENSHOCK_FW_CHIP_NAME "ESP32-S2"
+// GPIO44, GPIO43 is used for UART0 RXD/TXD.
+// GPIO29, GPIO26, GPIO32, GPIO31, GPIO30, GPIO28, GPIO27 is used for SPI flash connection. (DO NOT TOUCH)
+// GPIO0, GPIO45, GPIO46 is strapping pins used to control the boot mode and misc. functions.
+#define CHIP_UNSAFE_GPIO(pin) (pin == GPIO_NUM_44 || pin == GPIO_NUM_43 || pin == GPIO_NUM_29 || pin == GPIO_NUM_26 || pin == GPIO_NUM_32 || pin == GPIO_NUM_31 || pin == GPIO_NUM_30 || pin == GPIO_NUM_28 || pin == GPIO_NUM_27 || pin == GPIO_NUM_0 || pin == GPIO_NUM_45 || pin == GPIO_NUM_46)
+#endif
+
+// ESP32-S3
+//
+// Chips: ESP32-S3, ESP32-S3FN8, ESP32-S3R2, ESP32-S3R8, ESP32-S3R8V, ESP32-S3R16V, ESP32-S3FH4R2
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp32-s3_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP32S3
+#define OPENSHOCK_FW_CHIP_NAME "ESP32-S3"
+// GPIO44, GPIO43 is used for UART0 RXD/TXD.
+// GPIO30, GPIO29, GPIO26, GPIO32, GPIO31, GPIO28, GPIO27, GPIO33, GPIO34, GPIO35, GPIO36, GPIO37 is used for SPI flash connection. (DO NOT TOUCH)
+// GPIO0, GPIO3, GPIO45, GPIO46 is strapping pins used to control the boot mode and misc. functions.
+#define CHIP_UNSAFE_GPIO(pin) (pin == GPIO_NUM_44 || pin == GPIO_NUM_43 || pin == GPIO_NUM_30 || pin == GPIO_NUM_29 || pin == GPIO_NUM_26 || pin == GPIO_NUM_32 || pin == GPIO_NUM_31 || pin == GPIO_NUM_28 || pin == GPIO_NUM_27 || pin == GPIO_NUM_33 || pin == GPIO_NUM_34 || pin == GPIO_NUM_35 || pin == GPIO_NUM_36 || pin == GPIO_NUM_37 || pin == GPIO_NUM_0 || pin == GPIO_NUM_3 || pin == GPIO_NUM_45 || pin == GPIO_NUM_46)
+#endif
+
+// ESP32-S3-PICO-1
+//
+// Chips: ESP32-S3-PICO-1-N8R2, ESP32-S3-PICO-1-N8R8
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp32-s3-pico-1_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP32S3PICO1
+#define OPENSHOCK_FW_CHIP_NAME "ESP32-S3-PICO-1"
+#error "ESP32-S3-PICO-1 is not supported yet."
+#endif
+
+// ESP32-C3
+//
+// Chips: ESP32-C3, ESP32-C3FN4, ESP32-C3FH4, ESP32-C3FH4AZ
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp32-c3_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP32C3
+#define OPENSHOCK_FW_CHIP_NAME "ESP32-C3"
+#error "ESP32-C3 is not supported yet."
+#endif
+
+// ESP32-C6
+//
+// Chips: ESP32-C6, ESP32-C6FH4
+//
+// Docs: https://www.espressif.com/sites/default/files/documentation/esp32-c6_datasheet_en.pdf
+#ifdef OPENSHOCK_FW_CHIP_ESP32C6
+#define OPENSHOCK_FW_CHIP_NAME "ESP32-C6"
+#error "ESP32-C6 is not supported yet."
+#endif
+
+#pragma endregion
+
+/// Board specific bad-pin bypasses for compatibility reasons.
+/// To be clear, these pins are still unsafe, but we need to use them for compatibility reasons.
+#pragma region Board Specific Bypasses
+
+#ifdef OPENSHOCK_FW_BOARD_WEMOSD1MINIESP32
+#define OPENSHOCK_BYPASSED_GPIO(pin) (pin == 15)
+#endif
+#ifdef OPENSHOCK_FW_BOARD_WEMOSLOLINS2MINI
+#define OPENSHOCK_BYPASSED_GPIO(pin) (pin == 15)
+#endif
+#ifdef OPENSHOCK_FW_BOARD_PISHOCK2023
+#define OPENSHOCK_BYPASSED_GPIO(pin) (pin == 12)
+#endif
+#ifdef OPENSHOCK_FW_BOARD_PISHOCKLITE2021
+#define OPENSHOCK_BYPASSED_GPIO(pin) (pin == 15)
+#endif
+#ifdef OPENSHOCK_FW_BOARD_SEEEDXIAOESP32S3
+#define OPENSHOCK_BYPASSED_GPIO(pin) (pin == 21)
+#endif
+#ifdef OPENSHOCK_FW_BOARD_OPENSHOCKCOREV1
+#define OPENSHOCK_BYPASSED_GPIO(pin) (pin == 15)
+#endif
+#ifndef OPENSHOCK_BYPASSED_GPIO
+#define OPENSHOCK_BYPASSED_GPIO(pin) (false)
+#endif
+
+#pragma endregion
+
+#define OPENSHOCK_IS_VALID_GPIO(pin) ((pin < GPIO_NUM_MAX && !CHIP_UNSAFE_GPIO(pin)) || OPENSHOCK_BYPASSED_GPIO(pin))
+#define OPENSHOCK_IS_VALID_INPUT_GPIO(pin) ((OPENSHOCK_IS_VALID_GPIO(pin) && (GPIO_IS_VALID_GPIO(pin) && !GPIO_IS_VALID_OUTPUT_GPIO(pin))) || OPENSHOCK_BYPASSED_GPIO(pin))
+#define OPENSHOCK_IS_VALID_OUTPUT_GPIO(pin) ((OPENSHOCK_IS_VALID_GPIO(pin) && GPIO_IS_VALID_OUTPUT_GPIO(pin)) || OPENSHOCK_BYPASSED_GPIO(pin))
+
+namespace OpenShock {
+  constexpr bool IsValidGPIOPin(std::uint8_t pin) {
+    return OPENSHOCK_IS_VALID_GPIO(pin);
+  }
+  constexpr bool IsValidInputPin(std::uint8_t pin) {
+    return OPENSHOCK_IS_VALID_INPUT_GPIO(pin);
+  }
+  constexpr bool IsValidOutputPin(std::uint8_t pin) {
+    return OPENSHOCK_IS_VALID_OUTPUT_GPIO(pin);
+  }
+  constexpr std::bitset<UINT8_MAX+1> GetValidGPIOPins() {
+    std::bitset<UINT8_MAX+1> pins;
+    for (std::uint8_t i = 0; i < GPIO_NUM_MAX; i++) {
+      if (IsValidGPIOPin(i)) {
+        pins.set(i);
+      }
+    }
+    return pins;
+  }
+  constexpr std::bitset<UINT8_MAX+1> GetValidInputPins() {
+    std::bitset<UINT8_MAX+1> pins;
+    for (std::uint8_t i = 0; i < GPIO_NUM_MAX; i++) {
+      if (IsValidInputPin(i)) {
+        pins.set(i);
+      }
+    }
+    return pins;
+  }
+  constexpr std::bitset<UINT8_MAX+1> GetValidOutputPins() {
+    std::bitset<UINT8_MAX+1> pins;
+    for (std::uint8_t i = 0; i < GPIO_NUM_MAX; i++) {
+      if (IsValidOutputPin(i)) {
+        pins.set(i);
+      }
+    }
+    return pins;
+  }
+}  // namespace OpenShock

include/Constants.h

@@ -1,5 +1,7 @@
 #pragma once
 
+#include "Chipset.h"
+
 #include <cstdint>
 
 #ifndef OPENSHOCK_API_DOMAIN
@@ -19,6 +21,8 @@
 #ifndef OPENSHOCK_RF_TX_GPIO
 #warning "OPENSHOCK_RF_TX_GPIO is not defined, using default value of UINT8_MAX"
 #define OPENSHOCK_RF_TX_GPIO UINT8_MAX
+#elif !OPENSHOCK_IS_VALID_OUTPUT_GPIO(OPENSHOCK_RF_TX_GPIO)
+#error "OPENSHOCK_RF_TX_GPIO is not a valid output GPIO, and is not declared as bypassed by board specific definitions, refusing to compile"
 #endif
 
 namespace OpenShock::Constants {

scripts/embed_env_vars.py

@@ -45,9 +45,17 @@ def get_git_commit() -> str | None:
 
 # Find env variables based on only the pioenv and sysenv.
 def get_pio_firmware_vars() -> dict[str, str | int | bool]:
+    fw_board = pio.get_string('PIOENV')
+    fw_chip = pio.get_string('BOARD_MCU')
+
+    def macroify(s: str) -> str:
+        return s.upper().replace('-', '').replace('_', '')
+
     vars = {}
-    vars['OPENSHOCK_FW_BOARD'] = pio.get_string('PIOENV')
-    vars['OPENSHOCK_FW_CHIP'] = pio.get_string('BOARD_MCU')
+    vars['OPENSHOCK_FW_BOARD'] = fw_board
+    vars['OPENSHOCK_FW_BOARD_' + macroify(fw_board)] = True  # Used for conditional compilation.
+    vars['OPENSHOCK_FW_CHIP'] = fw_chip
+    vars['OPENSHOCK_FW_CHIP_' + macroify(fw_chip)] = True  # Used for conditional compilation.
     vars['OPENSHOCK_FW_MODE'] = pio_build_type
     git_commit = get_git_commit()
     if git_commit is not None:

src/CommandHandler.cpp

@@ -1,6 +1,6 @@
 #include "CommandHandler.h"
 
-#include "Board.h"
+#include "Chipset.h"
 #include "config/Config.h"
 #include "Constants.h"
 #include "Logging.h"