For dance gamers stuck at home and looking to bring an old pad back to life or build a new one. <3
FSR stands for Force-Sensitive Resistor. It is a thin piece of conductive material used to recognize varying degrees of pressure. At rest the FSR's resistance is close to infinity, but it decreases when pressure is applied. As the resistance goes down, the voltage in the circuit goes up. The voltage can be measured, and its value indicates the amount of pressure on the sensor.
- Thin profile: they easily fit under the panels of both arcade and home pads, allowing to try them out with minimal modification to pad structure. They are also easy to incorporate into a home-made pad.
- Precise performance: with good firmware, FSR pads perform as good as well-modded pads with arcade sensors.
- Variable sensitivity: each sensor's threshold can be adjusted individually, without touching the pads. Each player can store their own sensitivity profile.
- Decoupling pad feel from sensitivity: raising or lowering the panels no longer affects sensitivity, making it possible to adjust these qualities separately.
You will need:
- An Arduino that can communicate via USB. You probably want something that uses an ATmega32U4 controller, for example an Arduino Leonardo, an Arduino Micro, or a Teensy 2. Ensure that your board has enough analog pins to accommodate the number of sensors you wish to connect. You may want to order one with pre-soldered pins.
- FSRs, at least one per panel. They come in different shapes and withstand different pressures. I use FSR406 and FSR402.
- Resistors. They prevent the FSR from short-circuiting. Experiment with resistance values to get a good sensitivity range, which will depend on the type of FSR. I use 330 Ohm.
- Wires, to connect the FSRs and the board. If in doubt, search for "jumper wire" and get a variety of connectors (F-F, M-M, M-F). They can be chained together to make a longer wire.
- A breadboard to prototype the circuit. The breadboard can stay forever in the control box if you don't feel like soldering anything.
- Tape to fix the FSRs to the pad, and to create a pressure point. You may also need electrical tape to isolate the wires from the pad.
- (optional) Clincher connectors to secure the wire to the FSRs. The wires will be less likely to fall off during the session, though mine were taped together and did pretty well for a while.
Below is a board with 4 sensors attached. Highlighted is part of the circuit serving one sensor. The pins on your Arduino will differ, refer to the manual to find the right ones. Position of wires on the breadboard matters! If you are unsure how a breadboard works, read this intro guide.
Points of interest:
- V — the voltage pin on the board.
- A — an analog pin which measures voltage.
- FSR — the FSR is connected with two wires, off-picture.
- R — the pulldown resistor that prevents short-circuiting.
- GND — the ground pin on the board.
| Breadboard | Diagram |
|---|---|
 |
 |
If you wish to use more than one FSR per panel, connect them in parallel to the same resistor and pin. Pressing any of the FSRs will trigger the panel. You may also connect them to separate pins, and bind the pins to one key press.
To interpret voltage readings, you will need to program your board with an Arduino sketch. At a minimum, the sketch should read voltage on the pins, and determine whether or not it is higher than a certain threshold. When it is, the board should send a keystroke or a joystick button press. A more advanced sketch would also linearize the voltage and handle double-triggering.
While you don't necessarily need any software to use the board, it is helpful to at least output sensor readings to the command line for debugging. It could also be helpful to have an interface to change sensor thresholds and reload the sketch to the board.
Here are three existing FSR dance pad repositories worth checking out:
- mckyla-fsr provides a sketch for a 4-sensor pad, as well as a web interface to change sensitivity. It includes player profiles, which is great for multiple-user setups. It also provides a mode that finds an optimal threshold to reduce double-triggering from vibrations.
- analog-dance-pad contains lightweight firmware specifically for Teensy 2, and a web application to configure sensitivity. It allows to set sensor thresholds individually, has real-time pressure visualization, and facilitates 1000Hz polling.
- teejusb's fsr does mostly the same stuff but with a different UI/sketch. Supports all Teensy and most Arduino boards.
Pick an existing firmware + UI combination above, or roll your own, and the sensors should be ready to go! Verify that they register pressure and send back a key or a joystick button press. Then head to Stepmania input options, and bind the key presses to the corresponding panels.
Tape the sensors to the L-bracket or the frame in your pad, so that they are in contact with the panel. The sensor may not respond well if the pressure from the panel is distributed elsewhere. To fix this, put 1-2 layers of tape size of a thumbnail onto the center of the sensor. The pressure will go into this area first, making the sensors a lot more responsive. If your panels bend a lot, like in Cobalt Flux and similar home pads, reinforce the areas under the panels with some firm material, such as linoleum or tape.
Installation example: one FSR on the L-bracket in the up panel, two FSRs on dedicated brackets in the left panel. The control box is stored under the upper left metal panel.
Questions, corrections, feedback? Come over to discussions!