Hardware monitoring and external watchdog support for the Raspberry Pi
PiDog2 is a software + hardware device to make the Raspberry Pi very robust for applications where it will be deployed remotely, potentially with solar and battery power, and with out human access or intervention for months or years.
It is designed to deal with the scenarios like:
* what if the application on my Raspberry Pi locks up?
* what if the Raspberry Pi itself locks up?
* what if my power source fails or a battery is depleted?
* what if the power source recharges?
Furthermore, PiDog2 can really help save power when the system only needs to operate for part of the day. If you need a sensor read or a photo taken a few times day, or maybe even less frequently, then why leave the Pi powered at all times? Instead, the PiDog2 makes it easy to wake the Pi, run your app, then have the Pi shutdown again for a wakeup at a (potentially much) later time. The result: power saved, letting you get by with perhaps a smaller battery and solar system than you would need for continuous 24x7 operation.
PiDog2 attaches to the RPi's GPIO header and acts as an SPI slave capable of powering and un-powering the Pi completely. Instead of connecting power to your RPi, you connect it to the PiDog. The PiDog, in turn provides power to the Pi through the 5V GPIO pins.
With this arrangement, the PiDog can "hard reboot" a Pi by "yanking the cord" if the dog had not been fed after a certain period. Later, the PiDog can re-apply power to the Pi and let the Pi boot again.
Just summarily pulling the power is notfriendly, however, so that situation is to be avoided. The PiDog can help with that as well, allowing a Pi to bring itself to a halt before power-down and then expect to be woken again after a period.
-
Standard watchdog: wait a period of time, then turn off the device
-
Wake-dog: wait a period of time and then turn the device back on again.
-
Provides voltage measurements to the Pi of the 5V input, the 5V output, the Pi's 3.3V rail, and up to do separate measurements, intended for measurement of a 12V battery and ... anything else that comes to mind.
-
detect and deal with a Pi that has become unresponsive, ie, yank the cord and plug it back in
-
allow a Pi to shut down gracefully to save power, then wake it later when conditions are better. Basically, the Pi can adjust the watchdog power off time to a minute or so, then initiate a shutdown sequence itself. The Pi has a chance to reach an halted state and then the power is cut. After a predetermiend interval, the PiDog can power the Pi back up and it can boot, check battery status, etc, and depending on conditions shut itself down again or continue normally.
-
monitor battery and charging system health. Provie that info to a Pi so that it can decide to shut itself down, etc.
The PiDog hardware is based on a small circuit board about the exact size of the Pi Zero. (And yes, it works with Pi Zero.) It contains a processor (AtTiny84) and a P-FET power switch with ample capacity to power any RPi. There is also a micro USB port for power as well as 0.1" headers for power, a JST connections for a 12V battery monitoring, and some debug headers and LEDs.
Power consumption for the PiDog is about 14 mA when operating with the Pi on. In this state, it will respond to SPI transactions. When the Pi is off, the PiDog switches to lower-power mode, about 4mA including the LEDs. SPI transactions won't work in this mode, but then again, there is no RPi to make them, so it's probably OK.
The PiDog2 can easily switch on and off any Raspberry Pi, be it a zero through 3B+. It can also switch on any peripherals you may have connected through the USB ports. Attention was paid to using wide power traces on the circuit board and using a transistor with a lower on-resistance so that the voltage drop from input to output while on would be as low as possible. Even up to 2.5A draw, the voltage drop on the switched 5V node should not be more than 100mV lower than the input. (Note that the PiDog cannot do anything about the voltage drop at the input under load. If you see a significant voltage drop from your power supply, you may want to investigate a beefier 5V supply.
The PiDog has the following connectors:
1. The 2x20 pin connector for the Raspberry Pi (JRPI)
The PiDog connects the following pins on the RPi;
- all grounds
- The 5V pins
- The 3V3 pins
- MISO,MOSI,SCK,and CS0 (for the SPI interface and
programming)
2. a micro-USB connector (JUSB). You can connect any USB power supply here.
3. A 2x2 0.1" header for power (JPWR). With the text upright, the left
two pins on this header are both grounds. The lower pin is the
input 5V line (the same as the 5V line on the USB connector) and
the upper right pin is the switched 5V line. This is the 5V that
the Pi sees.
You can temporarily jumper the upper and lower right pins so that the
Pi's 5V line is always powered regardless of the PiDog's on/off
status. This is convenient for firmware updates and while experimenting
with the PiDog's firmware and output registers.
4. a 2x3 AVR-style programming header (JICSP). If you want to use
an AVR programmer, you can do so from this connector, though you
probably will never need to, since the firmware can be upgraded
from the Pi itself.
5. A debug header (JDBG). The output pins that drive the two programmable
LEDs (D30_1 and D30_2) can double as serial debug pins. This is
enabled by setting a macro in the firmware sketch, recompiling,
and reprogramming. Obviously, the LEDs will no longer function
normally in this mode. This can be very useful for firmware
development.
Of course, you can use these pins for anything else you want, too,
if you are willing to change the firmware.
6. The voltage measuring ports: JSENSA and JSENSB. This 2-pin JST
connectors have voltage dividers between them and the attiny, so
that you can safely measure any voltage up to about 16V. You can,
of course, change those resistors to different values for
different ranges. My intentino was that these would be used to
monitor a battery voltage, but they can be used for other
purposes as well.
Firmware running on the AtTiny makes it appear as an SPI device to the RPi. To the RPi, it looks like a bunch of registers. On the RPi, a Python library is provided that talks SPI to the device. Various functions allow feeding the timer, adjusting parameters, and reading status.
You do not need an AVR device programmer to re-program the Attiny device. The RPi can do it directly! This allows in-situ firmware updates, and even remote firmware updates if you dare!
- More cooked library support for the shutdown/wakeup use case, perhaps with awareness of weather and solar availability
PiDog2 is based on an earlier piece of hardware that I have deployed in various remote sensing applications. The main change with this version is adding voltage measurement, switching to an AtTiny (from a 328p) and switchign to SPI from i2c.
- HW version v0.7, SW version : 0.0.1
-
What Raspberry Pi's does it work with?
So far, tested with the Pi3 and Pi Zero. I expect others will work, too.
-
How much power does it consume?
It runs off the 5V rail. It draws about 14mA when the Pi is on (plus the Pi power, of course) and 4mA when the Pi is off. Some of that power is in the voltage dividers for the voltage sensing, so you can remove those resistors if you do not need the voltages, and some of the power is in LEDs, which you can turn off.
-
How accurate is the timing?
There is no crystal on this board. The Attiny is using its own internal 8 MHz clock, and everything timing-wise is divided down from that. It is probably accurate to a few percent.
When the device is in Pi-off mode, it uses a different low power oscillator that is part of the Attiny's own watchdog circuit. This oscillator runs as 128 kHz and is expected to be less accurate.
The long and the short of it is that if you want to turn off your Pi and expect to be woken 8 hours later, it might be 7 hours and 45 minutes or 8 hours and 15 minutes. You will have to do some experimentation, and consider using smaller intervals than you expect.
-
Where can I buy this?
Tindie!
Dave Jacobowitz
dave -at- southberkeleyelectronics.com
The code and files contained in this repository are subject to the GPLv3, a copy of which is included in the repository as well.
Artwork (gerbers) for the PCB itself is not included in this repository and is not licensed.