-
Notifications
You must be signed in to change notification settings - Fork 536
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
Merge pull request #422 from simplefoc/feat_new_cs_align
Feat new cs align
- Loading branch information
Showing
25 changed files
with
770 additions
and
600 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
93 changes: 93 additions & 0 deletions
93
examples/hardware_specific_examples/SimpleFOCMini/open_loop/open_loop.ino
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
| @@ -0,0 +1,93 @@ | ||
| /** | ||
| * | ||
| * SimpleFOCMini motor control example | ||
| * | ||
| * For Arduino UNO or the other boards with the UNO headers | ||
| * the most convenient way to use the board is to stack it to the pins: | ||
| * - 12 - ENABLE | ||
| * - 11 - IN1 | ||
| * - 10 - IN2 | ||
| * - 9 - IN3 | ||
| * | ||
| */ | ||
| #include <SimpleFOC.h> | ||
|
|
||
|
|
||
| // BLDC motor & driver instance | ||
| BLDCMotor motor = BLDCMotor(11); | ||
| // BLDCDriver3PWM driver = BLDCDriver3PWM(11, 10, 9, 8); // mini v1.0 | ||
| BLDCDriver3PWM driver = BLDCDriver3PWM(9, 10, 11, 12); // mini v1.1 | ||
|
|
||
| // instantiate the commander | ||
| Commander command = Commander(Serial); | ||
| void doMotor(char* cmd) { command.motor(&motor, cmd); } | ||
|
|
||
| void setup() { | ||
| // use monitoring with serial | ||
| Serial.begin(115200); | ||
| // enable more verbose output for debugging | ||
| // comment out if not needed | ||
| SimpleFOCDebug::enable(&Serial); | ||
|
|
||
| // if SimpleFOCMini is stacked in arduino headers | ||
| // on pins 12,11,10,9,8 | ||
| // pin 12 is used as ground | ||
| pinMode(12,OUTPUT); | ||
| pinMode(12,LOW); | ||
|
|
||
| // driver config | ||
| // power supply voltage [V] | ||
| driver.voltage_power_supply = 12; | ||
| driver.init(); | ||
| // link the motor and the driver | ||
| motor.linkDriver(&driver); | ||
|
|
||
| // aligning voltage [V] | ||
| motor.voltage_sensor_align = 3; | ||
|
|
||
| // set motion control loop to be used | ||
| motor.controller = MotionControlType::velocity_openloop; | ||
|
|
||
| // default voltage_power_supply | ||
| motor.voltage_limit = 2; // Volts | ||
|
|
||
| // comment out if not needed | ||
| motor.useMonitoring(Serial); | ||
|
|
||
| // initialize motor | ||
| motor.init(); | ||
| // align encoder and start FOC | ||
| motor.initFOC(); | ||
|
|
||
| // add target command M | ||
| command.add('M', doMotor, "motor"); | ||
|
|
||
| Serial.println(F("Motor ready.")); | ||
| Serial.println(F("Set the target velocity using serial terminal:")); | ||
|
|
||
| motor.target = 1; //initial target velocity 1 rad/s | ||
| Serial.println("Target velocity: 1 rad/s"); | ||
| Serial.println("Voltage limit 2V"); | ||
| _delay(1000); | ||
| } | ||
|
|
||
| void loop() { | ||
| // main FOC algorithm function | ||
| // the faster you run this function the better | ||
| // Arduino UNO loop ~1kHz | ||
| // Bluepill loop ~10kHz | ||
| motor.loopFOC(); | ||
|
|
||
| // Motion control function | ||
| // velocity, position or voltage (defined in motor.controller) | ||
| // this function can be run at much lower frequency than loopFOC() function | ||
| // You can also use motor.move() and set the motor.target in the code | ||
| motor.move(); | ||
|
|
||
| // function intended to be used with serial plotter to monitor motor variables | ||
| // significantly slowing the execution down!!!! | ||
| // motor.monitor(); | ||
|
|
||
| // user communication | ||
| command.run(); | ||
| } |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Oops, something went wrong.