The PX4 SITL stack comes with a sitl_multiple_run.sh
shell script that runs multiple instances of the PX4 binary. This would allow the SITL stack to listen to connections from multiple AirSim vehicles on multiple TCP ports starting from 4560.
However, the provided script does not let us view the PX4 console. If you want to run the instances manually while being able to view each instance's console (Recommended) see this section
Note you have to build PX4 with make px4_sitl_default none_iris
as shown here before trying to run multiple PX4 instances.
-
From your bash (or Cygwin) terminal go to the PX4 Firmware directory and run the
sitl_multiple_run.sh
script while specifying the number of vehicles you needcd PX4-Autopilot ./Tools/sitl_multiple_run.sh 2 # 2 here is the number of vehicles/instances
This starts multiple instances that listen to TCP ports 4560 to 4560+i where 'i' is the number of vehicles/instances specified
-
You should get a confirmation message that says that old instances have been stopped and new instances have been started
killing running instances starting instance 0 in /cygdrive/c/PX4/home/PX4/Firmware/build/px4_sitl_default/instance_0 starting instance 1 in /cygdrive/c/PX4/home/PX4/Firmware/build/px4_sitl_default/instance_1
-
Now edit AirSim settings file to make sure you have matching TCP port settings for the set number of vehicles and to make sure that both vehicles do not spawn on the same point.
For example, these settings would spawn two PX4Multirotors where one of them would try to connect to PX4 SITL at port
4560
and the other at port4561
. It also makes sure the vehicles spawn at0,1,0
and0,-1,0
to avoid collision:{ "SettingsVersion": 1.2, "SimMode": "Multirotor", "Vehicles": { "Drone1": { "VehicleType": "PX4Multirotor", "UseSerial": false, "UseTcp": true, "TcpPort": 4560, "ControlPortLocal": 14540, "ControlPortRemote": 14580, "X": 0, "Y": 1, "Z": 0 }, "Drone2": { "VehicleType": "PX4Multirotor", "UseSerial": false, "UseTcp": true, "TcpPort": 4561, "ControlPortLocal": 14541, "ControlPortRemote": 14581, "X": 0, "Y": -1, "Z": 0 } } }
You can add more than two vehicles but you will need to make sure you adjust the TCP port for each (ie: vehicle 3's port would be
4562
and so on..) and adjust the spawn point. -
Now run your Unreal AirSim environment and it should connect to SITL PX4 via TCP. If you are running the instances with the PX4 console visible, you should see a bunch of messages from each SITL PX4 window. Specifically, the following messages tell you that AirSim is connected properly and GPS fusion is stable:
INFO [simulator] Simulator connected on UDP port 14560 INFO [mavlink] partner IP: 127.0.0.1 INFO [ecl/EKF] EKF GPS checks passed (WGS-84 origin set) INFO [ecl/EKF] EKF commencing GPS fusion
If you do not see these messages then check your port settings.
-
You should also be able to use QGroundControl with SITL mode. Make sure there is no Pixhawk hardware plugged in, otherwise QGroundControl will choose to use that instead. Note that as we don't have a physical board, an RC cannot be connected directly to it. So the alternatives are either use XBox 360 Controller or connect your RC using USB (for example, in case of FrSky Taranis X9D Plus) or using trainer USB cable to your PC. This makes your RC look like a joystick. You will need to do extra set up in QGroundControl to use virtual joystick for RC control. You do not need to do this unless you plan to fly a drone manually in AirSim. Autonomous flight using the Python API does not require RC, see
No Remote Control
.
If you want to start your SITL instances while being able to view the PX4 console, you will need to run the shell scripts found here rather than sitl_multiple_run.sh
.
Here is how you would do so:
Note This script also assumes PX4 is built with make px4_sitl_default none_iris
as shown here before trying to run multiple PX4 instances.
-
From your bash (or Cygwin) terminal go to the PX4 directory and get the scripts (place them in a subdirectory called Scripts win the PX4 directory as shown)
cd PX4 mkdir -p Scripts cd Scripts wget https://github.com/microsoft/AirSim/raw/main/PX4Scripts/sitl_kill.sh wget https://github.com/microsoft/AirSim/raw/main/PX4Scripts/run_airsim_sitl.sh
Note the shell scripts expect the
Scripts
andFirmware
directories to be within the same parent directory. Also, you may need to make the scripts executable by runningchmod +x sitl_kill.sh
andchmod +x run_airsim_sitl.sh
. -
Run the
sitl_kill.sh
script to kill all active PX4 SITL instances./sitl_kill.sh
-
Run the
run_airsim_sitl.sh
script while specifying which instance you would like to run in the current terminal window (the first instance would be numbered 0)./run_airsim_sitl.sh 0 # first instance = 0
You should see the PX4 instance starting and waiting for AirSim's connection as it would with a single instance.
______ __ __ ___ | ___ \ \ \ / / / | | |_/ / \ V / / /| | | __/ / \ / /_| | | | / /^\ \ \___ | \_| \/ \/ |_/ px4 starting. INFO [px4] Calling startup script: /bin/sh /cygdrive/c/PX4/home/PX4/Firmware/etc/init.d-posix/rcS 0 INFO [dataman] Unknown restart, data manager file './dataman' size is 11798680 bytes INFO [simulator] Waiting for simulator to connect on TCP port 4560
-
Open a new terminal and go to the Scripts directory and start the next instance
cd PX4 cd Scripts ./run_airsim_sitl.sh 1 # ,2,3,4,..,etc
-
Repeat step 4 for as many instances as you would like to start
-
Run your Unreal AirSim environment and it should connect to SITL PX4 via TCP (assuming your settings.json file has the right ports).