Create single-nic-vm-host-with-vlans.md

doc/howto.md

@@ -29,6 +29,7 @@ creating-link-aggregation
 dbus-config
 netplan-everywhere
 single-nic-vm-host
+single-nic-vm-host-with-vlans
 ```
 
 

doc/single-nic-vm-host-with-vlans.md

@@ -0,0 +1,239 @@
+# How to configure a VM host with a single network interface and three VLANs
+
+This guide shows how to configure a virtual machine (VM) host using Netplan and the `virsh` interface. The host in this scenario has a single network interface (NIC) and three VLAN networks.
+
+
+## Prerequisites
+
+Ensure the following prerequisites are satisfied.
+
+
+### System
+
+- Computer with a single network interface card (NIC).
+- Ubuntu Server installed.
+- KVM and QEMU installed; see [KVM installation](https://help.ubuntu.com/community/KVM/Installation).
+- Administrator privileges.
+
+
+### Networking
+
+- IPv4:
+  - VLAN1 untagged (management), IPv4: 192.168.150.0/24
+  - VLAN40 tagged (guest), IPv4: 192.168.151.0/24
+  - VLAN41 tagged (dmz), IPv4: 192.168.152.0/24
+  - DNS1: 1.1.1.1
+  - DNS2: 8.8.8.8
+- Switch with [VLAN](https://en.wikipedia.org/wiki/VLAN) support
+- Router with [VLAN](https://en.wikipedia.org/wiki/VLAN) support
+  - VLAN1 IPv4: 192.168.150.254/24
+  - VLAN40 IPv4: 192.168.151.254/24
+  - VLAN41 IPv4: 192.168.152.254/24
+  - InterVLAN routing, DNS, and DHCP configured
+- Firewall configured; see [UFW](https://help.ubuntu.com/community/UFW).
+
+
+#### Disable netfilter for bridged interfaces
+
+To allow communication between the host server, its virtual machines, and the devices in the local VLANs, disable netfilter for bridged interfaces:
+
+1. Add the following lines to the `/etc/systemctl.conf` configuration file:
+
+    ```
+    net.bridge.bridge-nf-call-iptables = 0
+    net.bridge.bridge-nf-call-ip6tables = 0
+    net.bridge.bridge-nf-call-arptables = 0
+    ```
+
+2. Apply the changes immediately, without rebooting the host.
+
+    ```none
+    sysctl -p /etc/sysctl.conf
+    ```
+
+
+## Netplan configuration
+
+Configure Netplan:
+
+- Disable DHCP on the NIC.
+- Create two VLANs (40 and 41).
+- Create three bridge interfaces, and assign IPv4 addresses to them:
+  - `br0`: bridge on the untagged VLAN1 and the management interface of the server
+  - `br0-vlan40`: bridge on `vlan40`
+  - `br0-vlan41`: bridge on `vlan41`
+- Configure routes.
+- Configure DNS.
+
+1. To achieve this, modify the Netplan configuration file, `/etc/netplan/00-installer-config.yaml`,  as follows:
+
+    ```yaml
+    # network configuration:
+    # eno1 - untagged vlan1
+    # eno1-vlan40 - VLAN interface to connect to tagged vlan40
+    # eno1-vlan41 - VLAN interface to connect to tagged vlan41
+    # br0 - bridge for interface eno1 on untagged vlan1
+    # br0-vlan40 - bridge on tagged vlan40
+    # br0-vlan41 - bridge on tagged vlan41
+
+    network:
+      version: 2
+      ethernets:
+        eno1:
+          dhcp4: false
+      vlans:
+        eno1-vlan40:
+          id: 40
+          link: eno1
+        eno1-vlan41:
+          id: 41
+          link: eno1
+      bridges:
+        br0:
+          interfaces: [eno1]
+          dhcp4: false
+          addresses: [192.168.150.1/24]
+          routes:
+            - to: default
+              via: 192.168.150.254
+              metric: 100
+              on-link: true
+          nameservers:
+            addresses: [1.1.1.1, 8.8.8.8]
+            search: []
+        br0-vlan40:
+          interfaces: [eno1-vlan40]
+          dhcp4: false
+          routes:
+            - to: 0.0.0.0
+              via: 192.168.151.254
+              metric: 100
+              on-link: true
+          nameservers:
+            addresses: [1.1.1.1, 8.8.8.8]
+        br0-vlan41:
+          interfaces: [eno1-vlan41]
+          dhcp4: false
+          routes:
+            - to: 0.0.0.0
+              via: 192.168.152.254
+              metric: 100
+              on-link: true
+          nameservers:
+            addresses: [1.1.1.1, 8.8.8.8]
+    ```
+
+2. Test the new network settings:
+
+    ```none
+    netplan try
+    ```
+
+3. Apply the configuration:
+
+    ```
+    netplan apply
+    ```
+
+
+## Configure virtual networks using `virsh`
+
+The next step is to configure virtual networks defined for `virsh` domains. This is not necessary, but it makes VM deployment and management easier.
+
+
+### Check networking and delete the default network
+
+1. Check existing virtual networks:
+
+    ```none
+    virsh net-list --all
+    ```
+
+   There should be one default network as in this example:
+
+    ```
+    Name      State    Autostart   Persistent
+    --------------------------------------------
+    default   active   yes         yes
+    ```
+
+   If needed, use the `net-info` command to gather more details about the default network:
+
+    ```
+    virsh net-info default
+    ```
+
+2. Remove the default network:
+
+    ```
+    virsh net-destroy default
+    virsh net-undefine default
+    ```
+
+3. Check network list to confirm the changes have been applied. There should no networks defined now:
+
+    ```none
+    virsh net-list --all
+    ```
+
+
+### Create bridged networks
+
+1. Create a directory for VM data. For example:
+
+    ```none
+    mkdir /mnt/vmstore/
+    cd /mnt/vmstore/
+    ```
+
+2. Define the bridge interface, `br0`, for VLAN1 by creating the `/mnt/vmstore/net-br0.xml` file with  the following contents:
+
+    ```xml
+    <network>
+        <name>br0</name>
+        <forward mode="bridge" />
+        <bridge name="br0" />
+    </network>
+    ```
+
+3. Define the bridge interface, `br0-vlan40`, for VLAN40 by creating the `/mnt/vmstore/net-br0-vlan40.xml` file with  the following contents:
+
+    ```xml
+    <network>
+        <name>br0-vlan40</name>
+        <forward mode="bridge" />
+        <bridge name="br0-vlan40" />
+    </network>
+    ```
+
+4. Define the bridge interface, `br0-vlan41`, for VLAN41 by creating the `/mnt/vmstore/net-br0-vlan41.xml` file with  the following contents:
+
+    ```xml
+    <network>
+        <name>br0-vlan41</name>
+        <forward mode="bridge" />
+        <bridge name="br0-vlan41" />
+    </network>
+    ```
+
+5. Enable the virtual (bridged) networks. This consists of three steps (performed for each of the networks):
+
+   1. Define the network.
+   2. Start  the network.
+   3. Set the network to autostart.
+
+    ```
+    virsh net-define net-br0.xml
+    virsh net-define net-br0-vlan40.xml
+    virsh net-define net-br0-vlan41.xml
+    virsh net-start br0
+    virsh net-start br0-vlan40
+    virsh net-start br0-vlan41
+    virsh net-autostart br0
+    virsh net-autostart br0-vlan40
+    virsh net-autostart br0-vlan41
+    ```
+
+6. Test the bridged networks.
+
+Congratulations, the configuration is complete. You can now create a virtual machine, assign the desired network using your preferred VM configuration tool, and run some tests.