Add support of CH390H both in esp_eth and its examples . Latest PR! (IDFGH-12264)

components/esp_eth/CMakeLists.txt

@@ -52,6 +52,11 @@ if(CONFIG_ETH_ENABLED)
                          "src/esp_eth_phy_ksz8851snl.c")
     endif()
 
+    if(CONFIG_ETH_SPI_ETHERNET_CH390)
+        list(APPEND srcs "src/esp_eth_mac_ch390.c"
+                         "src/esp_eth_phy_ch390.c")
+    endif()
+
     if(CONFIG_ETH_USE_OPENETH)
         list(APPEND srcs "src/esp_eth_mac_openeth.c"
                          "src/esp_eth_phy_dp83848.c")

components/esp_eth/Kconfig

@@ -156,6 +156,17 @@ menu "Ethernet"
                 The KSZ8851SNL is a single-chip Fast Ethernet controller consisting of
                 a 10/100 physical layer transceiver (PHY), a MAC, and a Serial Peripheral Interface (SPI).
                 Select this to enable KSZ8851SNL driver.
+
+        config ETH_SPI_ETHERNET_CH390
+            bool "Use CH390"
+            help
+                CH390 is an industrial-grade Ethernet controller IC with 10/100M
+                Ethernet Media Transport Layer (MAC) and Physical Layer Transceiver (PHY),
+                supporting CAT3, 4, 5 and CAT5 and 6 connections for 10BASE-TX and 100BASE-TX,
+                supporting HP Auto-MDIX, low power design, and IEEE 802.3u compliant.
+                The CH390 has a built-in 16K byte SRAM, supports 3.3V or 2.5V parallel interface
+                and SPI serial interface.
+                Select this to enable KSZ8851SNL driver.
     endif # ETH_USE_SPI_ETHERNET
 
     menuconfig ETH_USE_OPENETH

components/esp_eth/include/esp_eth_mac.h

@@ -761,6 +761,45 @@ typedef struct {
 esp_eth_mac_t *esp_eth_mac_new_ksz8851snl(const eth_ksz8851snl_config_t *ksz8851snl_config, const eth_mac_config_t *mac_config);
 #endif // CONFIG_ETH_SPI_ETHERNET_KSZ8851
 
+#if CONFIG_ETH_SPI_ETHERNET_CH390
+/**
+ * @brief CH390 specific configuration
+ *
+ */
+typedef struct {
+    int int_gpio_num;                                   /*!< Interrupt GPIO number */
+    uint32_t poll_period_ms;                            /*!< Period in ms to poll rx status when interrupt mode is not used */
+    spi_host_device_t spi_host_id;                      /*!< SPI peripheral (this field is invalid when custom SPI driver is defined) */
+    spi_device_interface_config_t *spi_devcfg;          /*!< SPI device configuration (this field is invalid when custom SPI driver is defined) */
+    eth_spi_custom_driver_config_t custom_spi_driver;   /*!< Custom SPI driver definitions */
+} eth_ch390_config_t;
+
+/**
+ * @brief Default CH390 specific configuration
+ *
+ */
+#define ETH_CH390_DEFAULT_CONFIG(spi_host, spi_devcfg_p) \
+    {                                           \
+        .int_gpio_num = 0,                      \
+        .spi_host_id = spi_host,                \
+        .spi_devcfg = spi_devcfg_p,             \
+        .custom_spi_driver = ETH_DEFAULT_SPI,   \
+    }
+
+/**
+* @brief Create CH390 Ethernet MAC instance
+*
+* @param ch390_config: CH390 specific configuration
+* @param mac_config: Ethernet MAC configuration
+*
+* @return
+*      - instance: create MAC instance successfully
+*      - NULL: create MAC instance failed because some error occurred
+*/
+esp_eth_mac_t *esp_eth_mac_new_ch390(const eth_ch390_config_t *ch390_config, const eth_mac_config_t *mac_config);
+#endif
+
+
 #if CONFIG_ETH_USE_OPENETH
 /**
 * @brief Create OpenCores Ethernet MAC instance

components/esp_eth/include/esp_eth_phy.h

@@ -390,6 +390,20 @@ esp_eth_phy_t *esp_eth_phy_new_w5500(const eth_phy_config_t *config);
 */
 esp_eth_phy_t *esp_eth_phy_new_ksz8851snl(const eth_phy_config_t *config);
 #endif
+
+#if CONFIG_ETH_SPI_ETHERNET_CH390
+/**
+* @brief Create a PHY instance of CH390
+*
+* @param[in] config: configuration of PHY
+*
+* @return
+*      - instance: create PHY instance successfully
+*      - NULL: create PHY instance failed because some error occurred
+*/
+esp_eth_phy_t *esp_eth_phy_new_ch390(const eth_phy_config_t *config);
+#endif
+
 #ifdef __cplusplus
 }
 #endif

components/esp_eth/src/ch390.h

@@ -0,0 +1,199 @@
+/*
+ * SPDX-FileCopyrightText: 2024 Sergey Kharenko
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * SPDX-FileContributor: 2023-2024 NanjingQinhengMicroelectronics CO LTD
+ * SPDX-FileContributor: 2024 Sergey Kharenko
+ * SPDX-FileContributor: 2024 Espressif Systems (Shanghai) CO LTD
+ */
+#pragma once
+
+#include <stdint.h>
+
+/********************************************************************
+ * Register definition
+ */
+
+#define CH390_NCR       0x00
+    #define NCR_WAKEEN      (1<<6) // Enable wakeup function
+    #define NCR_FDX         (1<<3) // Duplex mode of the internal PHY
+    #define NCR_LBK_MAC     (1<<1) // MAC loop-back
+    #define NCR_RST         (1<<0) // Softwate reset
+#define CH390_NSR       0x01
+    #define NSR_SPEED       (1<<7) // Speed of internal PHY
+    #define NSR_LINKST      (1<<6) // Link status of internal PHY
+    #define NSR_WAKEST      (1<<5) // Wakeup event status
+    #define NSR_TX2END      (1<<3) // Tx packet B complete status
+    #define NSR_TX1END      (1<<2) // Tx packet A complete status
+    #define NSR_RXOV        (1<<1) // Rx fifo overflow
+    #define NSR_RXRDY       (1<<0)
+#define CH390_TCR       0x02
+    #define TCR_TJDIS       (1<<6) // Transmit jabber timer
+    #define TCR_PAD_DIS2    (1<<4) // PAD appends for packet B
+    #define TCR_CRC_DIS2    (1<<3) // CRC appends for packet B
+    #define TCR_PAD_DIS1    (1<<2) // PAD appends for packet A
+    #define TCR_CRC_DIS1    (1<<1) // CRC appends for packet A
+    #define TCR_TXREQ       (1<<0) // Tx request
+#define CH390_TSRA      0x03
+#define CH390_TSRB      0x04
+    #define TSR_TJTO        (1<<7) // Transmit jabber time out
+    #define TSR_LC          (1<<6) // Loss of carrier
+    #define TSR_NC          (1<<5) // No carrier
+    #define TSR_LCOL        (1<<4) // Late collision
+    #define TSR_COL         (1<<3) // Collision packet
+    #define TSR_EC          (1<<2) // Excessive collision
+#define CH390_RCR       0x05
+    #define RCR_DEFAULT     0x00   // Default settings
+    #define RCR_WTDIS       (1<<6) // Disable 2048 bytes watch dog
+    #define RCR_DIS_CRC     (1<<4) // Discard CRC error packet
+    #define RCR_ALL         (1<<3) // Pass all multicast
+    #define RCR_RUNT        (1<<2) // Pass runt packet
+    #define RCR_PRMSC       (1<<1) // Promiscuous mode
+    #define RCR_RXEN        (1<<0) // Enable RX
+#define CH390_RSR       0x06
+    #define RSR_RF          (1<<7) // Rnt frame
+    #define RSR_MF          (1<<6) // Multicast frame
+    #define RSR_LCS         (1<<5) // Late collision seen
+    #define RSR_RWTO        (1<<4) // Receive watchdog time-out
+    #define RSR_PLE         (1<<3) // Physical layer error
+    #define RSR_AE          (1<<2) // Alignment error
+    #define RSR_CE          (1<<1) // CRC error
+    #define RSR_FOE         (1<<0) // FIFO overflow error
+#define CH390_ROCR      0x07
+#define CH390_BPTR      0x08
+#define CH390_FCTR      0x09
+    #define FCTR_HWOT(ot)   (( ot & 0xf ) << 4)
+    #define FCTR_LWOT(ot)   ( ot & 0xf )
+#define CH390_FCR       0x0A
+    #define FCR_FLOW_ENABLE (0x39) // Enable Flow Control
+#define CH390_EPCR      0x0B
+    #define EPCR_REEP       (1<<5) // Reload EEPROM
+    #define EPCR_WEP        (1<<4) // Write EEPROM enable
+    #define EPCR_EPOS       (1<<3) // EEPROM or PHY operation select
+    #define EPCR_ERPRR      (1<<2) // EEPROM or PHY read command
+    #define EPCR_ERPRW      (1<<1) // EEPROM or PHY write command
+    #define EPCR_ERRE       (1<<0) // EEPROM or PHY access status
+#define CH390_EPAR      0x0C
+#define CH390_EPDRL     0x0D
+#define CH390_EPDRH     0x0E
+#define CH390_WCR       0x0F
+    #define WCR_LINKEN      (1<<5) // Link status change wakeup
+    #define WCR_SAMPLEEN    (1<<4) // Sample frame wakeup
+    #define WCR_MAGICEN     (1<<3) // Magic packet wakeup
+    #define WCR_LINKST      (1<<2) // Link status change event
+    #define WCR_SAMPLEST    (1<<1) // Sample frame event
+    #define WCR_MAGICST     (1<<0) // Magic packet event
+#define CH390_PAR       0x10
+#define CH390_MAR       0x16
+#define CH390_GPCR      0x1E
+#define CH390_GPR       0x1F
+#define CH390_TRPAL     0x22
+#define CH390_TRPAH     0x23
+#define CH390_RWPAL     0x24
+#define CH390_RWPAH     0x25
+#define CH390_VIDL      0x28
+#define CH390_VIDH      0x29
+#define CH390_PIDL      0x2A
+#define CH390_PIDH      0x2B
+#define CH390_CHIPR     0x2C
+#define CH390_TCR2      0x2D
+    #define TCR2_RLCP         (1<<6) // Retry Late Collision Packet
+#define CH390_ATCR      0x30
+    #define ATCR_AUTO_TX      (1<<7) // Auto-Transmit Control
+
+#define CH390_TCSCR     0x31
+    #define TCSCR_ALL         0x1F
+    #define TCSCR_IPv6TCPCSE  (1<<4) // IPv6 TCP checksum generation
+    #define TCSCR_IPv6UDPCSE  (1<<3) // IPv6 UDP checksum generation
+    #define TCSCR_UDPCSE      (1<<2) // UDP checksum generation
+    #define TCSCR_TCPCSE      (1<<1) // TCP checksum generation
+    #define TCSCR_IPCSE       (1<<0) // IP checksum generation
+#define CH390_RCSCSR    0x32
+    #define RCSCSR_UDPS     (1<<7) // UDP checksum status
+    #define RCSCSR_TCPS     (1<<6) // TCP checksum status
+    #define RCSCSR_IPS      (1<<5) // IP checksum status
+    #define RCSCSR_UDPP     (1<<4) // UDP packet of current received packet
+    #define RCSCSR_TCPP     (1<<3) // TCP packet of current received packet
+    #define RCSCSR_IPP      (1<<2) // IP packet of current received packet
+    #define RCSCSR_RCSEN    (1<<1) // Receive checksum checking enable
+    #define RCSCSR_DCSE     (1<<0) // Discard checksum error packet
+#define CH390_MPAR      0x33
+#define CH390_SBCR      0x38
+#define CH390_INTCR     0x39
+    #define INCR_TYPE_OD    0x02
+    #define INCR_TYPE_PP    0x00
+    #define INCR_POL_L      0x01
+    #define INCR_POL_H      0x00
+#define CH390_ALNCR     0x4A
+#define CH390_SCCR      0x50
+#define CH390_RSCCR     0x51
+#define CH390_RLENCR    0x52
+#define CH390_BCASTCR   0x53
+#define CH390_INTCKCR   0x54
+#define CH390_MPTRCR    0x55
+    #define MPTRCR_RST_TX   (1<<1) // Reset TX Memory Pointer
+    #define MPTRCR_RST_RX   (1<<0) // Reset RX Memory Pointer
+#define CH390_MLEDCR    0x57
+#define CH390_MRCMDX    0x70
+#define CH390_MRCMDX1   0x71
+#define CH390_MRCMD     0x72
+#define CH390_MRRL      0x74
+#define CH390_MRRH      0x75
+#define CH390_MWCMDX    0x76
+#define CH390_MWCMD     0x78
+#define CH390_MWRL      0x7A
+#define CH390_MWRH      0x7B
+#define CH390_TXPLL     0x7C
+#define CH390_TXPLH     0x7D
+#define CH390_ISR       0x7E
+    #define ISR_LNKCHG      (1<<5)  // Link status change
+    #define ISR_ROO         (1<<3)  // Receive overflow counter overflow
+    #define ISR_ROS         (1<<2)  // Receive overflow
+    #define ISR_PT          (1<<1)  // Packet transmitted
+    #define ISR_PR          (1<<0)  // Packet received
+    #define ISR_CLR_STATUS (ISR_LNKCHG | ISR_ROO | ISR_ROS | ISR_PT | ISR_PR)
+#define CH390_IMR       0x7F
+    #define IMR_NONE        0x00    // Disable all interrupt
+    #define IMR_ALL         0xFF    // Enable all interrupt
+    #define IMR_PAR         (1<<7)  // Pointer auto-return mode
+    #define IMR_LNKCHGI     (1<<5)  // Enable link status change interrupt
+    #define IMR_UDRUNI      (1<<4)  // Enable transmit under-run interrupt
+    #define IMR_ROOI        (1<<3)  // Enable receive overflow counter overflow interrupt
+    #define IMR_ROI         (1<<2)  // Enable receive overflow interrupt
+    #define IMR_PTI         (1<<1)  // Enable packet transmitted interrupt
+    #define IMR_PRI         (1<<0)  // Enable packet received interrupt
+
+// SPI commands
+#define OPC_REG_W       0x80  // Register Write
+#define OPC_REG_R       0x00  // Register Read
+#define OPC_MEM_DMY_R   0x70  // Memory Dummy Read
+#define OPC_MEM_WRITE   0xF8  // Memory Write
+#define OPC_MEM_READ    0x72  // Memory Read
+
+#define CH390_SPI_RD    0
+#define CH390_SPI_WR    1
+
+// GPIO
+#define CH390_GPIO1     0x02
+#define CH390_GPIO2     0x04
+#define CH390_GPIO3     0x08
+
+
+// PHY registers
+#define CH390_PHY          0x40
+#define CH390_PHY_BMCR     0x00
+#define CH390_PHY_BMSR     0x01
+#define CH390_PHY_PHYID1   0x02
+#define CH390_PHY_PHYID2   0x03
+#define CH390_PHY_ANAR     0x04
+#define CH390_PHY_ANLPAR   0x05
+#define CH390_PHY_ANER     0x06
+#define CH390_PHY_PAGE_SEL 0x1F
+
+// Packet status
+#define CH390_PKT_NONE  0x00    /* No packet received */
+#define CH390_PKT_RDY   0x01    /* Packet ready to receive */
+#define CH390_PKT_ERR   0xFE    /* Un-stable states */
+#define CH390_PKT_MAX   1536    /* Received packet max size */
+#define CH390_PKT_MIN   64